Introduction; Device Description (Fig. 1-22); Scope Of Delivery - Parkside PKZS 2000 A1 Originalbetriebsanleitung

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschine GmbH
Günzburger Straße 69
D- 89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the man-
ufacturer of the device does not assume liability for dam-
ages to the product or damages caused by the product that
occurs due to:
• Improper handling,
• Non- compliance of the operating instructions,
• Repairs by third parties, not by authorized service tech-
nicians,
• Installation and replacement of non- original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to
the non- compliance of the electric regulations and VDE
regulations 0100, DIN 57113 / V DE0113.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device.
The operating instructions are intended to help the user to
become familiar with the machine and take advantage of its
application possibilities in accordance with the recommen-
dations.
The operating instructions contain important information
on how to operate the machine safely, professionally and
economically, how to avoid danger, costly repairs, reduce
downtimes and how to increase reliability and service life
of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that ap-
ply for the operation of the machine in your country.
Keep the operating instructions package with the machine at
all times and store it in a plastic cover to protect it from dirt
and moisture. Read the instruction manual each time before
operating the machine and carefully follow its information.
The machine can only be operated by persons who were
instructed concerning the operation of the machine and who
are informed about the associated dangers. The minimum
age requirement must be complied with.
In addition to the safety instructions contained in this oper-
ating manual and the specific regulations of your country,
the technical rules generally accepted for the operation of
machines of the same type must be observed.
We accept no liability for damage or accidents which arise
due to non- observance of these instructions and the safety
information.

2. Device description (Fig. 1-22)

1. Handle
2. ON/OFF switch
3. Release lever
4. Machine head
5. Movable blade guard
6. Saw blade
7. Clamping device
8. Workpiece support
9. Locking screw for workpiece support
10. Table insert
11. Handle
12. Pointer
13. Scale
14. Turntable
15. Fixed saw table
16. Stop rail
16a. Moveable stop rail
16b. Set screw
17. Sawdust bag
18. Scale
19. Pointer
20. Locking screw for drag guide
21. Drag guide
22. Locking screw
23. Safety pin
24. Screw for cutting depth limiter
25. Stop for cutting depth limiter
26. Fastening bolt for turn table
27. Adjustment screw (90°)
28. Adjustment screw (45°)
29. Flange bolt
30. Outer flange
31. Saw shaft lock
32. Inner flange
33. Laser
34. ON/OFF switch for laser
35. Guide bar
a.) 90° stop angle (not supplied)
b.) 45° stop angle (not supplied)
c.) Spring
d.) Allen key, 6 mm
e.) Philips head screw (Laser)

3. Scope of delivery

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for transport damage.
• If possible, store the packaging until the warranty period
has expired.
ATTENTION
The device and packaging materials are not toys! Chil-
dren must not be allowed to play with plastic bags, film
and small parts! There is a risk of swallowing and suf-
focation!
GB/C Y 3