Technical Data - Parkside PKZS 2000 A1 Originalbetriebsanleitung

- When transporting the electric tool, only use the
transport devices. Never use the protective devices
for handling or transport.
- Operate the machine only if the protective devices
are functional, in good condition and in the correct
position.
- The floor around the machine must be level, clean
and free of loose particles, such as chips and cutting
residues.
- Only use saw blades for which the maximum permis-
sible speed is not lower than the maximum spindle
speed of the machine and which are suitable for the
material to be cut.
- Be sure to only use spacers and spindle rings speci-
fied by the manufacturer as suitable for the intended
purpose.
- Attention! Do not replace the laser by a different type.
Repairs may only be carried out by the manufacturer
or an authorized representative.
- Do not remove any cutting residues or other parts of
workpieces from the cutting zone while the machine
is running and the saw unit is not at rest.
Instructions for proper and safe sawing:
a.) Clamp the workpiece always at the saw table firmly.
Therefore please use the supplied clamping device.
b.) Make sure that the machine is secured before each
sawing;
c.) If necessary attach the machine to a workbench or the like.
Fasten the machine to the workbench, using the holes at
the fixed saw table.
d.) Support long workpieces (e.g. with a roller table) to
prevent them sagging at the end of a cut.
e.) Make sure that the saw blade does not touch the rotary
table in any position by pulling out the mains plug and
rotating the saw blade by hand in the 45° and 90° po-
sition. If necessary, readjust the saw head.
Warning! This electric tool generates an electromagnetic
field during operation. This field can impair active or pas-
sive medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recommend
that persons with medical implants consult with their physi-
cian and the manufacturer of the medical implant prior to
operating the electric tool.
Safety Instructions for the handling of saw blades
1. Only use insertion tools if you have mastered their use.
2. Observe the maximum speed. The maximum speed
specified on the insertion tool may not be exceeded. If
specified, observe the speed range.
3. Observe the motor / saw blade direction of rotation.
4. Do not use any insertion tools with cracks. Sort out
cracked insertion tools. Repairs are not permitted.
5. Clean grease, oil and water off of the clamping sur-
faces.
6. Do not use any loose reducing rings or bushes for the
reducing of holes on saw blades.
7. Make sure that fixed reducer rings for securing the in-
sertion tool have the same diameter and have at least
1/3 of the cutting diameter.
6 GB
8. Make sure that fixed reducer rings are parallel to each
other.
9. Handle insertion tool with caution. They are ideally
stored in the originally package or special containers.
Wear protective gloves in order to improve grip and to
further reduce the risk of injury.
10. Prior to the use of insertion tools, make sure that all pro-
tective devices are properly fastened.
11. Prior to use, make sure that the insertion tool meets the
technical requirements of this electric tool and is prop-
erly fastened.
12. Only use the supplied saw blade for cutting wood,
never for the processing of metals.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from accidents
using suitable precautionary measures!
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces
and persons or animals. Even a laser beam with a low out-
put can cause damage to the eyes.
• Caution - methods other than those specified here can re-
sult in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to
the beam can occur.
• The laser may not be replaced with a different type of la-
ser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.

6. Technical data

AC motor ...........................................220 - 240 V ~ 50Hz
Power................................................................1600 Watt
Operating mode ................................... S6 25%* 2000W
Idle speed n ...................................................5000 min
0
Carbide saw blade ..................... ø 254 x ø 30 x 3,0 mm
Number of teeth ............................................................60
Swivel range ..........................................-45° / 0°/ +45°
Mitre cut ............................................ 0° to 45° to the left
Saw width at 90° ........................................340 x 78 mm
Saw width at 45° ........................................240 x 78 mm
Saw width at 2 x 45° (double mitre cut) .. 240 x 42 mm
Protection class ................................................................ II
Weight ............................................................. ca. 15,5 kg
Laser class ........................................................................ 2
Wavelength of laser ............................................. 650 nm
Laser output .......................................................... < 1 mW
*S6, continuous operation periodic duty.
Identical duty cycles with a period at load followed by
a period at no load. Running time 10 minutes; duty cy-
cle is 25% of the running time.
-1