Technical Data; Troubleshooting Guide - Kärcher PGG 3/1 Originalbetriebsanleitung

Lock
4
2. Remove the cover.
3. Check the air filter insert for soiling. Clean the air fil-
ter if necessary or replace if damaged (see "Clean-
ing the air filter").
4. Fit the cover.
5. Close the lock or screw in and tighten the screw.
Cleaning the air filter
ATTENTION
Risk of damage
Penetrating dust can destroy the engine if the air filter
insert is absent.
Do not operate the device without an air filter insert.
1. Open the air filter (see "Checking the air filter").
2. Remove the air filter insert.
3. Wash the air filter insert in warm water and house-
hold cleaner then rinse with clear water.
Note: Dispose of the oil contaminated washing solu-
tion in an environmentally friendly manner.
4. Allow the air filter insert to dry.
5. Saturate the air filter insert in clean engine oil and
press out the excess oil.
6. Fit the air filter insert back into place.
7. Fit the cover.
8. Close the latches.
Changing oil
Perform the oil change on a warm engine.
1. Unscrew the oil dipstick.
Illustration E
Oil dipstick
1
Oil drain screw
2
2. Unscrew the oil drain screw with seal and catch the
escaping oil.
3. Screw in and tighten the oil drain screw with seal.
4. Position the device on a level surface.
5. Measure the correct quantity of engine oil (SAE
10W30) and fill through the oil dipstick hole.
6. Check the oil level (see "Starting up").
7. Screw in and tighten the oil dipstick.
8. Dispose of the old oil in accordance with the envi-
ronmental regulations.
Cleaning the settling cup
The settling cup separates water from the petrol.
1. Close the fuel cock.
2. Unscrew the settling cup.
Illustration F
Generator
Continuous output
Maximum short-term output
cos φ
Mains voltage
Phase
Frequency
Degree of protection
Insulation class
Design class
DC output
Voltage
current
Internal combustion engine
Engine type
Type
Cooling type
Engine capacity
Engine performance
Fuel type
Fuel tank capacity
Working time with a fully filled fuel tank
Engine oil volume
Oil type
Spark plug type
Battery
Working voltage of the battery
Dimensions and weights
Length
Width
10
Settling cup
1
Screw
2
3. Remove the settling cup with O-ring.
4. Clean the settling cup and O-ring using a non-in-
flammable solvent and allow to dry.
5. Fit the settling cup and O-ring and screw tight.
6. Open the fuel cock.
7. Check the seal between the settling cup and carbu-
rettor.
8. Close the fuel cock.
Checking and cleaning the spark plug
1. Pull off the spark plug connector.
Illustration G
Spark plug connector
1
Spark plug
2
2. Clean the region around the spark plug to prevent
dirt from entering the engine when the spark plug is
removed.
3. Unscrew the spark plug.
4. Replace a spark plug that has worn electrodes or a
broken insulator.
5. Check the electrode gap of the spark plug. Target
value 0.7...0.8 mm.
6. Check the spark plug seal for damage.
ATTENTION
Risk of damage
A loose spark plug can overheat and damage the
engine. An overtightened spark plug can damage
the thread in the engine.
Observe the following instructions for tightening the
spark plug.
7. Carefully screw the spark plug in by hand. Do not
cross the thread.
8. Screw the spark plug all the way in using the plug
spanner and the tighten as follows.
a Tighten a used spark plug by an additional 1/
8...1/4 turn.
b Tighten a new spark plug by an additional 1/2
turn.
9. Plug on the spark plug connector.
Charging the device battery
DANGER
Danger of explosion, risk of fire
Connecting the two battery terminals causes a short-cir-
cuit that can result in an explosion or fire.
Never place a metal object (e.g. a tool) on the battery.

Technical data

kW
kW
V
~
Hz
V
A
3
cm
kW/PS
h
l
V
mm
mm
English
Автотовары «130»
Danger of injury
Observe the safety instructions on the handling of bat-
teries.
Observe the operating instructions for the charger.
CAUTION
Health risk
Lead is harmful to your health.
Never allow lead to come into contact with open
wounds.
1. Check the battery acid level.
2. If the battery acid level is too low:
a Remove the cell cap.
b Top up the cell with distilled water up to the mark-
ing.
c Fit the cell cap.
3. Disconnect the battery.
4. Connect the plus cable of the charger to the plus ter-
minal of the battery.
5. Connect the minus cable of the charger to the minus
terminal of the battery.
6. Switch on the charger.

Troubleshooting guide

Have all checks and work on electrical parts performed
by an expert.
In case of any malfunctions not mentioned in this chap-
ter, contact the authorised Customer Service.
The engine does not start.
1. Open the fuel cock.
2. Fill the tank with fuel.
3. Check the oil level and top up if necessary.
4. Check the spark plug (see"Care and maintenance/
Checking and cleaning the spark plug").
5. Clean the settling cup (see "Care and Maintenance/
Cleaning the settling cup").
The device does not generate any electricity
1. Set the power switch to 1/ON.
The warranty conditions issued by our relevant sales
company apply in all countries. We shall remedy possi-
ble malfunctions on your appliance within the warranty
period free of cost, provided that a material or manufac-
turing defect is the cause. In a warranty case, please
contact your dealer (with the purchase receipt) or the
next authorised customer service site.
(See overleaf for the address)
PGG 3/1 PGG 6/1
2,8 5,0
3,0 5,5
1 1
230 (2x) 230 (3x)
1 1
50 50
IP23M IP23M
B B
G1 G1
12 12
6 6
Single-cylinder Single-cylinder
4-stroke 4-stroke
Air-cooled Air-cooled
208 389
5,1/6,9 9,6/13,1
Petrol, min. 86 octane Petrol, min. 86 octane
15 25
10 12
0,6 1,1
SAE 10W30 SAE 10W30
F5T, F6T, F7TJC F5T, F6T, F7TJC
12 12
645 743
622 713
Warranty
PGG 8/3
7,0
7,5
1
230 (2x), 400 (1x)
1 / 3
50
IP23M
B
G1
12
6
Single-cylinder
4-stroke
Air-cooled
439
11,8/16,1
Petrol, min. 86 octane
25
8
1,1
SAE 10W30
F5T, F6T, F7TJC
12
743
713