Additional Information; Troubleshooting - Pioneer CDJ-900NXS Bedienungsanleitung

Additional information

Troubleshooting

! Incorrect operation is often mistaken for trouble or malfunction. If you think that there is something wrong with this component, check the points
below. Sometimes the trouble may lie in another component. Inspect the other components and electrical appliances being used. If the trouble
cannot be rectified after checking the items below, ask your nearest Pioneer authorized service center or your dealer to carry out repair work.
! This unit may not operate properly due to such external causes as static electricity. If this happens, normal operation can sometimes be restored by
turning the power off, waiting for the disc to stop completely, then turning the power back on.
Problem
Disc cannot be ejected.
Playback does not start when disc
is loaded.
File cannot be played.
No sound is produced, or sound is
distorted or noisy.
Loud noise is produced or playback
stops when a certain disc is played.
File information is not properly
displayed.
Track search operation takes too long.
Back cue function does not work.
Loop play function does not work.
Settings are not stored in the memory. Has the power been turned off directly after
USB device is not recognized.
Cue points or loops are not stored on
a USB device.
Cue or loop points of tracks recorded
on USB devices are not displayed.
Playback does not start immediately
after pressing the button to reloop or
play in reverse.
The playing address display is not
displayed in the remaining time mode.
Time is required to read USB devices
(flash memory drives and hard discs).
Check
Is [EJECT/LOAD LOCK] set to [LOCK]?
—
Is the disc or file playable?
Is the auto cue function activated?
Is the file copyright-protected (by DRM)?
Are you operating the connected DJ mixer
properly?
Is this unit placed near a TV?
Is the disc scratched?
Is the disc dirty?
Is [LANGUAGE] properly set?
Is the information recorded in a language not sup-
ported by this unit?
Is the auto cue function activated?
—
Is a cue point set?
Are loop points set?
changing the setting?
Is the USB device properly connected?
Is the USB device connected via a USB hub?
Is the USB device supported by this unit?
Is the file format supported by this unit?
—
Are you trying to store more points than the limit?
Is the USB device write-protected?
Is there sufficient free space on the USB device?
Was the USB device properly stopped before it
was disconnected the last time?
Is the quantize function on?
—
Is there a large number of folders or files recorded
on the USB device?
Are files other than music files stored on the USB
device?
Remedy
Press the [PLAY/PAUSEf] button to set the pause mode, then press the
[DISC EJECTh] button.
Set [EJECT/LOAD LOCK] at [UTILITY] to [UNLOCK], then press the
[DISC EJECTh] button.
If the [DISC EJECTh] button does not work, insert the pin into the disc force
eject hole to eject the disc.
See Usable media on page 4.
Press [AUTO CUE] for at least 1 second to turn cancel the auto cue function.
Copyright-protected files cannot be played.
Check the operation of the DJ mixer.
Turn the TV's power off or install this unit and TV away from each other.
Scratched discs may not play.
Wipe the dirt off the disc.
Set [LANGUAGE] to the proper language.
When creating files using DJ software, etc., record the information in a language
supported by this unit.
Track searching may take some time when there are long silent sections
between tracks.
If track searching is not possible within 10 seconds, a cue point is set at the
beginning of the track.
Set a cue point.
Set loop points.
After changing settings, wait at least 10 seconds before turning the power off.
Connect the device securely (all the way in).
USB hubs cannot be used.
This player only supports USB mass storage class devices.
This player supports portable flash memory and digital audio playback devices.
Check the file format of the connected USB device. For the file formats sup-
ported by this unit, see About USB devices on page 4.
Turn the power off then back on.
A maximum of 100 cue or loop points can be stored on USB devices per disc. For
mediums other than discs, a maximum of 10 points can be stored per track.
If you try to store more points than the limit, [CUE/LOOPPOINT FULL] is dis-
played and the points cannot be stored. In this case, delete some points before
storing new ones.
If the USB device is write-protected, [USB FULL] is displayed and the points
cannot be stored. Disable the write-protection then store the cue or loop points
again.
If there is not enough free space on the USB device, [USB FULL] is displayed
and the points cannot be stored. Free up some space then store the cue or loop
points again.
Points may not be displayed if the SD memory card/USB device is removed
without performing the proper stopping procedure or if this unit's power is
turned off.
Check that the USB indicator has turned completely off before disconnecting
the USB device and turning this unit's power off.
When the quantize function is on, playback starts from the nearest beat position
at the time the button is pressed. If you want the operation to be performed the
instant the button is pressed, turn the quantize function off.
When playing files recorded in VBR, it may happen that the set cannot detect the
length of the track immediately and that some time is required for the playing
address display to appear.
When there are many folders or files, some time may be required for loading.
When files other than music files are stored in folders, time is required to read
them as well. Do not store files or folders other than music files on the USB device.
7
En