Pioneer CDJ-900NXS Bedienungsanleitung Seite 2

Thank you for buying this Pioneer product. Please read through these operating instructions so you will know how to operate your model properly. After
you have finished reading the instructions, put them away in a safe place for future reference.
In some countries or regions, the shape of the power plug and power outlet may sometimes differ from that shown in the explanatory drawings.
However the method of connecting and operating the unit is the same.
If you want to dispose this product, do not mix it with general household waste. There is a separate collection system for used
electronic products in accordance with legislation that requires proper treatment, recovery and recycling.
Private households in the member states of the EU, in Switzerland and Norway may return their used electronic products free of charge to
designated collection facilities or to a retailer (if you purchase a similar new one).
For countries not mentioned above, please contact your local authorities for the correct method of disposal.
By doing so you will ensure that your disposed product undergoes the necessary treatment, recovery and recycling and thus prevent potential
negative effects on the environment and human health.
CAUTION
TO PREVENT THE RISK OF ELECTRIC SHOCK, DO NOT
REMOVE COVER (OR BACK). NO USER-SERVICEABLE
PARTS INSIDE. REFER SERVICING TO QUALIFIED
SERVICE PERSONNEL.
WARNING
This equipment is not waterproof. To prevent a fire or
shock hazard, do not place any container filled with
liquid near this equipment (such as a vase or flower
pot) or expose it to dripping, splashing, rain or
moisture.
WARNING
To prevent a fire hazard, do not place any naked flame
sources (such as a lighted candle) on the equipment.
This product satisfies electromagnetic noise
regulations when it is connected to other equipment
through shielded cables and connectors.
Use only the furnished accessory connecting cables.
CAUTION
This product is a class 1 laser product classified
under the Safety of laser products, IEC 60825-1:2007.
CLASS 1 LASER PRODUCT
Condensation
Water droplets (condensation) may form inside the unit
(on operating parts and lenses) in the winter, for
example, if the unit is moved from a cold place into a
warm room or if the temperature in the room in which
the unit is installed rises suddenly (through heating,
etc.). The unit will not operate properly and will not be
playable with condensation inside. Let the unit stand for
1 to 2 hours at room temperature (though this time
depends on the conditions of the condensation) without
turning on the power. The water droplets will evaporate
and the unit will become playable. Condensation can
occur in the summer as well if the unit is exposed to the
direct wind from an air-conditioner, etc. If this happens,
move the unit to a different location.
2
En
Operating Environment
Operating environment temperature and humidity:
+5 °C to +35 °C (+41 °F to +95 °F); less than 85 %RH
(cooling vents not blocked)
Do not install this unit in a poorly ventilated area, or in
D3-4-2-1-1_B1_En
locations exposed to high humidity or direct sunlight (or
strong artificial light).
CAUTION
The
all power from the AC outlet. Since the power cord
D3-4-2-1-3_A1_En
serves as the main disconnect device for the unit,
you will need to unplug it from the AC outlet to shut
down all power. Therefore, make sure the unit has
been installed so that the power cord can be easily
unplugged from the AC outlet in case of an accident.
D3-4-2-1-7a_A1_En
To avoid fire hazard, the power cord should also be
unplugged from the AC outlet when left unused for a
long period of time (for example, when on vacation).
D44-8-2_A1_En
When using this product, confirm the safety
information shown on the bottom of the unit.
POWER-CORD CAUTION
Handle the power cord by the plug. Do not pull out the
plug by tugging the cord and never touch the power
cord when your hands are wet as this could cause a
short circuit or electric shock. Do not place the unit, a
D58-5-2-2a_A1_En
piece of furniture, etc., on the power cord, or pinch the
cord. Never make a knot in the cord or tie it with other
cords. The power cords should be routed such that they
are not likely to be stepped on. A damaged power cord
can cause a fire or give you an electrical shock. Check
the power cord once in a while. When you find it
damaged, ask your nearest PIONEER authorized
service center or your dealer for a replacement.
S005b_A1_En
switch on this unit will not completely shut off
K058b_A1_En
D3-4-2-1-7c*_A2_En
D3-4-2-2-2a*_A1_En
D3-4-2-2-4_B1_En
S002*_A1_En