Safety Information; Technical Data; Before Starting The Equipment; Attachment And Operation - Parkside PUG 1600 A1 Bedienungs- Und Sicherheitshinweise

The universal tool stand is also designed as a workpiece
support when working with mitre saws, scroll saws, circular
table saws, and other similar electric power tools.
The maximum workpiece length is 3 m.
Additional workpiece supports may have to be used (e.g.
a roller trestle) in order to prevent longer workpieces tilting.
Attention: Ensure that the workpiece support is secure and
not tilted!
Do not use the universal tool stand as a ladder or as scaf-
folding. Ensure that all handgrips, nuts and screws are tight-
ened before use. Electric power tools on this device shall not
exceed an overall height of 152 cm. The maximum payload
is 200 kg. Ensure that the universal tool stand is on a level,
firm and stable floor.
Any use beyond this is improper use. The manufacturer is not
responsible for the resultant damages, the user bears this
risk alone.
Please note that our equipment has not been designed for
use in commercial, trade or industrial applications. Our war-
ranty will be voided if the equipment is used in commercial,
trade or industrial businesses or for equivalent purposes.

5. Safety information

• Use the universal tool stand only in conjunction with suit-
able electric power tools!
• Check the universal tool stand for damage each time be-
fore use. Electric power tools shall not be mounted or op-
erated on damaged support arms / crossbars.
• Electric power tools must be bolted to the support arms /
crossbars and be secured on the universal tool stand!
• Always ensure the universal tool stand is secure when set-
ting it up.
• Always ensure that you assume a natural and safe stand-
ing position when working.
• Do not overload the universal tool stand! Do not use the
universal tool stand for purposes for which it is not intend-
ed.
• Modifications or unauthorised changes to the universal
tool stand as well as the use of unapproved parts is for-
bidden.
• All parts of the universal tool stand, in particular the safety
devices, must be correctly mounted in order to guarantee
trouble- free operation.
• Keep the universal tool stand out of reach of children.
Store the device in a location that is inaccessible to unau-
thorised persons and children.
m Attention!
When using electric power tools, in conjunction with the
universal tool stand, the respective machine- specific safety
measures must be implemented as protection against electric
shock, and the risk of injury or fire.
Read all of the instructions for the electric power tool that you
intend to mount and operate before using the tool.
Safety instructions for the electric device mounted must like-
wise be observed.
Store these safety instructions safely.
Observe all safety instructions. If you disregard the safety
instructions, you endanger yourself and others.

6. Technical data

Dimensions
1000 - 1650 x 580 x 810 - 910 mm
Table height
Height of the side expansions
Spacing of the supports
min. / max
Max. permissible payload
Weight in kg

7. Before starting the equipment

Check the device for transport damage. Immediately report
any damage to the transport company that delivered the de-
vice.

8. Attachment and operation

The universal tool stand is largely assembled and you need
only fit the handgrips and the workpiece supports as follows:
8.1 Erecting the universal tool stand (fig. 3-4)
Place the universal tool stand (A) on the floor or on a work-
bench such that the frame legs (A.1) point upwards.
Press the spring pins (M) and fold out the frame leg.
Once the spring pin latches into the intended position, the
frame leg is locked.
Repeat this process for the other frame legs.
Set the universal tool stand down on its feet.
8.2 Mounting support arms (Fig. 5)
Fit the support arms (B) to the frame bed (A) by pulling the
locking lever (B.3) upwards to unlock it and then latching the
arm into place on the frame base, firstly on the front side
(B.2).
Lower the rear side onto the bed and fasten the support arm
in place on the frame bed by pressing the locking lever (B.3).
Disassembly is carried out in reverse order.
8.3 Fitting the workpiece supports (fig. 6 - 7)
Insert the workpiece support (D) into the receiver (N) of the
frame bed and fasten in place with the star- grip screws (K).
The width and height of the workpiece supports can be ad-
justed with the star- grip screws (J, K). (Fig. 7)
8.4 Fastening your tabletop machine (fig. 8)
Different tabletop machines can be fastened to your univer-
sal tool stand by adjusting the support arms (B) to the spac-
ing of the mounting holes on your machine.
• Place your tabletop machine (e.g. mitre saw) on the sup-
port arms (B).
• Fasten the tabletop machine with 4 hexagonal screws (F),
4 washers (G), 4 spring washers (H) and 4 hexagonal nuts
(I) on each of the support arms.
750 mm
810 - 910 mm
1000 - 1650
mm
200 kg
ca. 13,3
GB/MT 13