Error Messages - Spokey HALLET II Bedienungsanleitung

The diagrams showing the successive programmes are available on
www.spokey.pl.
 Move the available values with your finger left/right on the screen to see
the next programmes
 The training time is set for 30 minutes by default. The training time can
be changed by clicking "+" or "-" icons
 Likewise, you can set the training target in "Time, calories and distance
countdown" programmes.
User Program
In this mode the user sets the parameters of his/her training. It is possible
to set 20 different user programmes.
 To select the user programme, go to the User program mode and select
"U4-U20"
 You can give a program its own name by clicking "Rename".
 To set the inclination angle of the running belt (Incline) in the next minutes
you should place the yellow dot on the appropriate value within the range
from 0-18%.
 To set the Speed in the next minutes you should drag the blue column to
the desired value within the range from 0,8-20 km/h.
ENTERTAINMENT APPLICATIONS
Available modes
Local Video – watching the film from the USB
Local Music – listening to the music from the USB
Training parameters preview
 During the use of entertainment applications you can see the
parameters of your training by clicking the ... icon.
 The information about the Speed, Inclination angle of the running belt
(Incline), Training Time (Time), Pulse value (Pulse), covered Distance
(Distance) and burnt Calories (Calories) will appear in the window.
E01 Controller communication failure
Possible causes: 1. The power cable is not appropriately connected. Check
the connection.
2. The controller is damaged or not appropriately placed
3. There is a problem with power supply to the controller, it needs to be
replaced
E02 Explosion protection
Possible causes: 1. Motor housing open or damaged motor. Replace the
motor or check the connection terminals.
2. Malfunction of the power cables. Replace the cables or the controller.
E03 No speed signal
Possible causes: 1. Damaged sensor, replace the sensor
2. The sensor is not appropriately placed, adjust its position.
E04 Malfunction of the motor lifting the running belt
Placing the treadmill, scope of usage
 The treadmill should be placed in a dry place, and not exposed to the
stream of water and moisture. The treadmill should be placed on a clean
and flat surface. Placing the treadmill on an uneven surface can cause
damage to its system. You cannot place the treadmill on a carpeted or
floor covering.
 The treadmill is intended for indoor use only.
 This equipment may not be exposed to an aerosol spray or oxygen.
Moreover, it may not be placed in areas where gas is used due to
possible sparks coming out of the engine.
 The user may change training parameters during the training,
depending on individual needs.
 The parameters (speed, inclination angle) can be changed using the
buttons on the console or on the treadmill handles.
 The training starts after clicking the Start inscription.
 The training ends by stopping the treadmill after the set training time or
achievement of the set target (burnt calories, distance). The user may
end the training (stop the treadmill) at any time by clicking the Stop
button..
 To set the Time select the desired value by clicking "+" or "-".
 The user may change training parameters during the training, depending
on individual needs.
 The parameters (speed, inclination angle) can be changed using the
buttons on the console or on the treadmill handles.
 The training starts after clicking the Start inscription.
 The training ends by stopping the treadmill after achievement of the set
training time. The user may end the training (stop the treadmill) at any
time by clicking the Stop button..
Online App – web browsers and access to social networks (Facebook,
Twitter, YouTube)
 The user may change training parameters during the training,
depending on individual needs.
 The parameters (speed, inclination angle) can be changed using the
buttons on the console or on the treadmill handles.
 The user may end the training (stop the treadmill) at any time by
clicking the Stop button.

ERROR MESSAGES

Cause: Failure of the motor responsible for changing the inclination angle
of the running belt, replace the motor
E05 Overload
Possible causes: 1. The device is overloaded (the maximum user's weight
has been exceeded)
2. The resistance of the running belt is too high, lubricate the running belt
3. Damaged motor, replace the motor
E06 POST controller error
Cause: Controller failure, replace the controller
E07 No parameters
Cause: The parameters cannot be displayed, replace the controller or
change retransmission parameters.
E08 Safety key
Cause: Removed safety key, put the key in place.
USAGE
 The treadmill should be placed at a distance of about 2 m from walls and
objects that may be dangerous to the user.
 The security area of 2 x 1 m must be left behind the exercise machine.
 Treadmill exercises replace walks and jogging. The treadmill is intended
for home use only and it is not designed for any therapeutic or
rehabilitation purposes.
 The device is not designed for a long-term operation or any commercial
activities.
11
www.spokey.eu