Operation - Parkside PTBM 710 A1 Bedienungs- Und Sicherheitshinweise

9.4 Assembling the handle (fig. 2)
1. Slide the handle (8) onto the retainer (D) as shown in fig. 2.
2. Place the handle (8) on the retainer (D) with the flattened
part at the side of the fastening screw (B).
3. Tighten the pre-assembled fastening screw (B) with the Allen
key (19).
9.5 Assembling the depth stop (fig. 2)
Insert the depth stop (7) into the hole provided in the housing.
9.6 Assembling the clamping lever for depth stop
(fig. 2)
Assemble the clamping lever for depth stop (6) as shown in
fig. 2.
9.7 Fastening to a work surface (fig. 3)
Fasten the device to the work surface by bolting the base plate
(1) to the work surface.

10. Operation

10.1 Operation of the display (fig. 4)
• Switching the display on/off:
Press the button (I, 2-3 sec.) until the display (9) switches
on or off.
• Display of drilling depth/speed:
The display can be switched between displaying the speed
and the drilling depth by pressing button (F).
• Setting the zero point:
The zero point for the drilling depth can be set by pressing
the button (G).
• Switching the laser cross on/off:
The laser cross can be switched on or off by pressing the
button (H).
• Switching the LED on/off:
The LED work light can be switched on or off by pressing
the button (I).
10.2 Height adjustment (fig. 1)
The position of the machine head can be adjusted to suit the
workpiece height or the workpiece length.
1. Hold the handle (8) firmly.
2. Release the clamping lever for the height adjustment (5).
3. Set the position of the machine head with the handle (8).
4. Secure the position of the machine head with the clamping
lever for height adjustment (5).
Attention! Ensure in the lowest machine head position that
the machine head will not be moved beyond the marking.
Use the clamping lever for height adjustment (5) to secure the
machine head in this position. Otherwise, the guide could be
damaged.
10.3 Setting the drilling depth (fig. 1)
The drilling depth can be set with the depth stop (7).
1. Release the clamping lever on the depth stop (6).
2. Carry out a test drilling. As soon as the desired depth is
shown on the display (9) (refer to point 10.9 also), tighten
the depth stop clamping lever (6) again.
3. The depth stop (7) is now locked in the desired drilling depth.
10.4 Clamping/releasing drill bits (fig. 5+7)
Clamping:
1. Hold the chuck in place and turn the securing ring (K) in the
"RELEASE" direction.
2. Turn the clamping sleeve (L) clockwise until the drill bit (M)
can be inserted. Hold the holding ring (J) in place whilst
doing so.
3. Insert the drill bit (M), hold it in place and turn the clamping
sleeve (L) counter-clockwise by hand. Hold the holding ring
(J) in place whilst doing so.
4. Hold the chuck in place and turn the securing ring (K) in the
"LOCK" direction.
Note: When using small drill bits, set the chuck to roughly the
right size for the drill bit beforehand. Otherwise there is a risk of
the drill bit not being properly centred in the chuck.
Releasing:
1. Turn the securing ring (K) in the "RELEASE" direction.
2. Turn the clamping sleeve (L) clockwise until the drill bit (M)
can be removed.
10.5 Aligning workpieces
1. Switch on the laser cross via the display (9). See 10.1, Op-
eration of the display.
2. The intersection of the two laser lines exactly indicates the
centre point of the drill.
3. Align your marking on the workpiece with the laser cross.
10.6 Clamping the workpiece (fig. 6)
It must be possible to clamp the workpiece securely. Do not
work with workpieces that cannot be clamped securely.
The cut-out of the quick clamp must be centrally aligned with
the hole to be drilled. Otherwise, the drill bit or the chuck could
be obstructed by the quick clamp.
1. Position the workpiece with the help of the laser cross.
2. Loosen the quick clamping lever (17).
3. Place the quick clamp (2) on the workpiece.
4. Turn the quick clamp lever (17) clockwise to clamp the work-
piece.
5. Turn the quick clamp lever (17) counter-clockwise to release
the quick clamp (2).
10.7 Clamping larger workpieces (fig. 6)
Use the parallel stop (16) for larger workpieces:
1. Loosen the wing screws for the parallel stop (15) and insert
the parallel stop (16) into the grooves of the base plate.
2. Tighten the wing screws for the parallel stop (15).
3. Align your workpiece against the parallel stop (16) and
clamp it with the quick clamp (2).
Warning! With workpieces that are wider or longer than the
tabletop, ensure that these are adequately supported, e. g.
through trestles or saw horses.
Workpieces that are longer or wider than the base plate of
the tabletop drill can tip if they are not properly supported. If
the workpiece tips, this can damage the chuck guard or the
cutting tool.
GB/IE 19