Drill Safety Warnings; Remaining Hazards - Parkside PTBM 710 A1 Bedienungs- Und Sicherheitshinweise

d) Store idle power tools out of the reach of chil-
dren and do not allow persons unfamiliar with
the power tool or these instructions to operate
the power tool.
Power tools are dangerous in the hands of untrained us-
ers.
e) Maintain power tools and accessories.
Check for misalignment or binding of moving parts, break-
age of parts and any other condition that may affect the
power tool's operation. If damaged, have the power tool
repaired before use. Many accidents are caused by poor-
ly maintained power tools.
f) Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting
edges are less likely to bind and are easier to
control.
g) Use the power tool, accessories and tool bits
etc. in accordance with these instructions, tak-
ing into account the working conditions and
the work to be performed.
Use of the power tool for operations different from those
intended could result in a hazardous situation.
h) Keep handles and grasping surfaces dry,
clean and free from oil and grease. Slippery han-
dles and grasping surfaces do not allow for safe handling
and control of the tool in unexpected situations.
Service
a) Have your power tool serviced by a qualified
repair person using only identical replacement
parts. This will ensure that the safety of the power tool
is maintained.

Drill safety warnings

a) The drill must be secured. A drill that is not properly
secured may move or tip over and may result in personal
injury.
b) The workpiece must be clamped or secured to
the workpiece support. Do not drill pieces that
are too small to be clamped securely. Holding
the workpiece by hand during operation may result in
personal injury..
c) Do not wear gloves. Gloves may be entangled by
the rotating parts or chips leading to personal injury.
d) Keep your hands out of the drilling area while
the tool is running. Contact with rotating parts or
chips may result in personal injury.
e) Make sure the accessory is rotating before
feeding into the workpiece. Otherwise the acces-
sory may become jammed in the workpiece causing un-
expected movement of the workpiece and personal injury.
f) When the accessory is jammed, stop applying
downward pressure and switch off the tool.
Investigate and take corrective actions to elim-
inate the cause of the jam. Jamming can cause un-
expected movement of the workpiece and personal injury.
g) Avoid generating long chips by regularly in-
terrupting downward pressure. Sharp metal
chips may cause entanglement and personal injuries.
h) Never remove chips from the drilling area
while the tool is running. To remove chips,
move the accessory away from the workpiece,
switch off the tool and wait for the accessory
to stop moving. Use tools such as a brush or
hook to remove chips. Contact with rotating parts or
chips may result in personal injury.
i) Accessories with speed ratings must be rated
at least equal to the maximum speed marked
on the power tool. Accessories running faster than
their rated speed can break and fly apart.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output
can cause damage to the eyes.
• Caution - methods other than those specified here can result
in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to the
beam can occur.
• The laser may not be replaced with a different type of laser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.
• Labelling and placement of warning stickers, see fig. 8 and 9.
Warning! This electric tool generates an electromagnetic field
during operation. This field can impair active or passive medi-
cal implants under certain conditions. In order to prevent the
risk of serious or deadly injuries, we recommend that persons
with medical implants consult with their physician and the man-
ufacturer of the medical implant prior to operating the electric
tool.

Remaining hazards

Even if you use this electric power tool in accord-
ance with instructions, certain residual risks can-
not be eliminated. Remaining hazards can be
minimized by following the instructions in „Safety
instructions", „Intended Use" and in the entire op-
erating manual. The following hazards may arise
in connection with the equipment's construction
and layout:
• Lung damage if suitable dust protection mask is not worn.
• Hearing damage if suitable hearing protection is not worn.
• Damage to health resulting from hand/arm vibration if the
device is used over an extended period of time or if it is not
properly operated and maintained.
GB/IE 17