Assembly And Attachment Of Tools And Tool Parts; Safety Instructions For Handling The Laser; Safety Instructions For Handling Batteries; Residual Risks - Parkside PTK 2000 E3 Originalbetriebsanleitung

GB IE
vices are correctly attached.
9 Before use, ensure that all of the tools used by you fulfil the
technical requirements of this power tool and are properly
attached.
10 The saw blade supplied should only be used for sawing
wood and never for working metal.
Assembly and Attachment
of Tools and Tool Parts
a) Tools and tool bodies must be tightened in such a way that
they cannot become loose during operation.
b) Attachment bolts and nuts are to be tightened to the torques
specified by the manufacturer using appropriate spanners etc.
c) Extending a spanner or tightening with the help of hammer
blows is not permitted.
d) The tightening surfaces must be cleaned to remove any dirt,
grease, oil and water.
e) Tensioning bolts must be tightened in accordance with the
manufacturer's instructions.
f) In order to adjust the borehole diameter of circular saw
blades to the spindle diameter of the machine, only firmly
inserted rings, e.g. rings which have been pressed into place
or which are held in place by means of an adhesive bond,
may be used. The use of loose rings is not permitted.
g) Ensure that fixed reducing rings are positioned parallel to
one another.
Safety Instructions
for Handling the Laser
– Caution: Laser radiation - Do not look into the beam - Laser
class 2
– The label is attached to the saw blade guard (2) near the
laser (35).
Safety Instructions
for Handling Batteries
1 Ensure at all times that the batteries are inserted with the
correct polarity (+ and –), as shown on the battery itself.
2 Do not short-circuit the batteries.
3 Do not charge non-rechargeable batteries.
4 Do not overcharge the battery!
5 Do not mix old and new batteries or batteries of a different
type or from different manufacturers! Replace all batteries of
a set at the same time.
6 Remove used batteries immediately out of the device and
dispose of them correctly!
7 Do not heat the batteries!
8 Do not carry out any welding or soldering work directly to
the batteries!
9 Do not take the batteries apart!
10 Do not deform the batteries!
11 Do not throw the batteries into the fire!
12 Store the batteries out of the reach of children.
13 Do not allow children to replace the batteries without
supervision!
14 Do not store the batteries close to a fire, cookers or other
sources of heat. Do not place the battery in direct sunlight
and do not use or store it in motor vehicles in hot weather.
26
15 Store used batteries in the original packaging and keep them
away from metal objects. Do not mix (up) unpacked batte-
ries! Otherwise this may cause the battery to short-circuit,
resulting in damage, burns or even the danger of fire.
16 Remove batteries from the device if this is not going to be
used for a prolonged period, unless it is to be used in emer-
gencies!
17 NEVER touch batteries which have leaked without appro-
priate protection. If the leaked liquid comes into contact with
the skin, you should rinse off this area of the skin immedia-
tely under running water. Make sure at all events that your
eyes and mouth do not come into contact with the liquid. If
they do, seek medical advice immediately.
18 Clean the battery contacts and the equivalent contacts in the
device before inserting the batteries.

Residual Risks

This power tool has been constructed in accordance
with the latest technology and the generally recog-
nised safety regulations. Nevertheless, it is possible
that individual residual risks may occur during opera-
tion.
• Electrical hazard if improper electrical connection cables are
used.
• In addition, concealed residual risks may be present in spite
of all the precautions that have been taken.
• Residual risks can be minimised by observing the „Safety
instructions" and „Use in accordance with the designated
purpose", as well as the operating instructions.
• Do not put any unnecessary stresses on the machine: exces-
sive pressure during sawing will quickly damage the saw
blade. This may result in a reduction in the performance of
the machine, as well as a reduction in the cutting accuracy.
• Avoid switching the machine on by accident: when inserting
the plug into the socket, the power button must not be pressed.
• Use the tool which is recommended in this manual. This will
ensure the optimal performance of your saw.
• Keep your hands away from the working area when the
machine is in operation.
• Before you carry out any adjustments or servicing work, turn
the device off and remove the mains plug.

Electrical Connection

The installed electric motor is connected ready for
operation. The connection complies with the relevant
BS standards. The customer's network connection and
any extension cable used must comply with these
regulations.
• The product meets the requirements of EN 61000-3-11 and
is subject to special connection conditions. This means that
its use at freely selectable connection points is not permitted.
• If the network conditions are unfavourable, the device may
result in temporary voltage fluctuations.
• The maximum permitted mains impedance at the electrical
connection point of 0.5367 ohm must not be exceeded.
• As the user, you must ensure – in consultation with your
electricity supply company if necessary – that the continuous
current carrying capacity of the network at the connection