Herunterladen Inhalt Inhalt Diese Seite drucken

Operation; Cleaning; Maintenance - Parkside PDUW 280 A1 Originalbetriebsanleitung

Druckluft-universalwerkzeug
Vorschau ausblenden Andere Handbücher für PDUW 280 A1:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

9. Operation

Changing the tool insert
m Risk of injury due to tools! Depressurise the
device before each tool change.
Always wear protective gloves when changing
tools!
Wear safety goggles!
Only original tools from the manufacturer may be used.
Inserting tool (fig. 2-3)
1 Hold the compressed air device with the tool receiver (3)
upwards. Support the other end on the ground.
2 Insert the tool (7-11) into the tool receiver (3) with the
hex. in the required orientation).
3 At the same time, pull down the adapter sleeve (with
circlip) (4). The insert tool (7-11) should now slide into the
receptacle. Now return the clamping sleeve (with locking
ring) (4).
4 The insert tool (7-11) is mounted correctly if it can not be
pulled out of the tool holder (3).
Removing the tool insert from the machine:
5 Slide the sliding sleeve (with circlip) (4) halfway down-
wards.
6 With the other hand pull out the insert tool (7-11). Guide
the clamping sleeve (with retaining ring) (4) back into
place again.
m Attention! Risk of injury! Every time the tool is
changed, ensure that the tool receiver (3) has no signs of
severe wear or heavy impacts. Otherwise, the tools can fall
out of the tool holder.
Connect hose (Fig. 4)
Check the compressed air hoses and couplings for leaks. In
the event of leaks, interrupt the compressed air supply and
replace the hose.
1 Connect the hose (not included in the delivery) to the
compressed air source (e.g. on the compressor) and
open the compressed air feed.
2 Connect the hose (1A) to the connection (1) on the
compressed air device. In doing so, ensure that the
compressed air device does not start up autonomously. If
this is the case, disconnect the compressed air coupling
immediately. Have the compressed air device repaired
by a specialist workshop or the manufacturer.
Working with the device
m Attention! Risk of injury! Never point the de-
vice at people or animals.
Keep other people or animals away from the work area and
keep a safe distance.
NOTE! The striking mechanism of the device only
operates when the tool is in contact with the ma-
terial to be processed. This function is designed
to protect the device against damage.
1 Press the trigger lever (6) to supply the impact mecha-
nism with compressed air and start the compressed air
device.
2 Always hold the compressed air device with both hands
during work:
– Hold the compressed air tool with one hand on the
shaft (5) or handle (2) and the other hand on the
trigger lever (6).
3 Note! Operate the Universal Air Tool only when insert
tool (7-11) is in contact with the material. Strokes with no
load lead to increased wear on the tool.
4 Too powerful levering can result in the shaft (5) or the
tools (7-11) breaking.
m Danger of stumbling!
5 If you release the trigger lever (6), the compressed air
feed is interrupted. The compressed air device stops with
a brief run-on time. m Risk of injury! Never lock the
trigger lever (6).
Check that the tool receiver has been furnished with an oil
film, after 2 hours of operation at the latest. If this is not the
case, introduce a few drops of special oil into the connection
hose (1).
The hexagon of the insert tool (7-11) should be greased
regularly.
Too little lubrication can cause damage to the Universal Air
Tool and Insert Tool (7-11).
End of work
• Remove the compressed air hose from the universal
pneumatic tool.
• Remove the insert tool from the universal pneumatic tool.

10. Cleaning

Keep the equipment free of dirt and dust as far as possible.
Wipe the equipment with a clean cloth or blow it down with
compressed air at low pressure.
• We recommend that you clean the equipment immediately
after you use it.
• Clean the Multi-Purpose Air Tool with a cloth. Do not use
any chemical cleaning agent. Ensure that all moveable
parts are oiled.
• Clean the equipment regularly with a damp cloth and some
soft soap. Do not use cleaning agents or solvents; these
may be aggressive to the plastic parts in the equipment. En-
sure that no water can get into the interior of the equipment.

11. Maintenance

Separate the machine from the compressed air supply before
any maintenance work or cleaning.
Wear safety goggles and a suitable dust mask for all mainte-
nance and cleaning work
If skin comes into contact with dangerous dust this can lead
to severe dermatitis.
Dust can be inhaled if it is generated or dispersed during
maintenance work.
If the regular oil supply to the device is assured, the
device is maintenance-free.
We recommend that all moving parts are properly lubricated
before every use (see fig. 6).
GB
7

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Inhaltsverzeichnis