Husqvarna AUTOMOWER 305 Kurzanleitung Seite 6

For more information and instructions, read the complete Operator's manual on the Husqvarna website
(www.husqvarna.com)
1. PL AC E M E N T O F A N D CO N N EC T I N G T H E C H A RG I N G S TAT I O N
1. Place the charging station at a central position in the working area, with a lot of open space in front of the charging station
and on a relatively horizontal surface.
2. Connect the power supply's low voltage cable to the charging station and the power supply.
3. Connect the power supply to a 100-240 V wall socket.
4. Place the robotic lawn mower in the charging station to charge the battery while the boundary wire is laid. Press the ON/OFF
button for 3 seconds and make sure that the indicator lamp on the button is lit.
2. PL AC E M E N T O F T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Lay the boundary wire so that it forms a loop around the working area.
2. Make an eyelet at the point where the guide wire will later be connected.
3. Run the guide wire to the point on the boundary loop where the connection will be made. Avoid laying the wire at tight
angles.
3. CO N N EC T I N G T H E B O U N DA RY W I R E A N D T H E G U I D E W I R E
1. Narrow passages in the yard make it difficult for the robotic lawn mower to find the charging station. The robotic lawn mower
can be lead to remote areas using the guide wire. The guide wire also helps the robotic lawn mower to quickly find the
charging station.
2. Lay the guide wire under the charging station and at least 2 m / 7 ft straight out from the front edge of the charging station.
3. Open the connectors and lay the wire ends in the recesses on each connector.
4. Press the connectors together using a pair of pliers.
5. Cut off any surplus boundary wire. Cut 1-2 cm / 0.4-0.8" above the connectors.
6. Press the connectors onto the contact pins, marked AL (left) and AR (right), on the charging station. It is important that the
right-hand wire is connected to the right-hand contact pin, and the left-hand wire to the left-hand pin.
7. Fasten the connector to the contact pin marked G1 on the charging station.
4. CO N N EC T I N G T H E G U I D E W I R E TO T H E B O U N DA RY W I R E
1. Cut the boundary wire with a wire cutters at the centre of the eyelet that was made in step 2.2.
2. Connect the guide wire to the boundary wire using the accompanying couplers. Press the couplers completely together with
a polygrip.
S TA R T I N G A N D S TO PPI N G
STARTING
1. Open the cover by pressing the STOP button.
2. Press the ON/OFF button for 3 seconds. When you do this for the first time, a start up sequence starts where you select a
four digit PIN code among other things.
3. Press the START button and close the cover.
STOPPING
Press the STOP button.
A D J U S T I N G T H E RO B OT I C L AW N M O W E R TO S U I T T H E S I Z E O F YO U R L AW N
The mowing results depend on mowing time. Adjust the mowing time to suit your yard using the Schedule function. You decide
what times during the day the robotic lawn mower is to work. The robotic lawn mower cut approximately 55 m² / 590 ft² per
hour and day. For example; if your yard consists of 500 m² / 5400 ft² of lawn, the robotic lawn mower should work 9 hours a
day.
M A I N T E N A N C E
1. Press the ON/OFF button for 3 seconds to disable the product and check that the indicator lamp on the button is not lit
before all work on the robotic lawn mower's chassis, such as cleaning or replacing the blades. Replace the blades regularly
for the best mowing result.
2. Never use a high-pressure washer to clean the robotic lawn mower. Never use solvents for cleaning. Clean the product with
a brush or running water from a water hose.
3. All connections to the charging station (power supply, boundary and guide wire) must be disconnected if there is a risk of a
thunderstorm.
4. Fully charge the battery at the end of the season before winter storage.
QG_P12_1141898_2020.indd 6
E N
2019-10-24 15:19:34