Herunterladen Inhalt Inhalt Diese Seite drucken

General Notes; Assembly - Parkside PDS 120 B2 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

8.2 General notes

• All covers and safety devices have to be properly fitted be-
fore the equipment is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed before,
watch out for foreign bodies such as nails or screws, etc.
• Before you actuate the On/Off switch, make sure that the
saw blade is correctly fitted and that the equipment's moving
parts run smoothly.
• Check that the voltage on the rating plate is the same as
your supply voltage before you connect the equipment to
the power supply.
• Only ever connect the equipment to a properly installed
shock-proof socket which is protected by a 10A fuse as a
minimum.
8.3 Installing the fretsaw on a workbench
Required for installing:
Included in the scope of delivery:
• M8 hex screw (4x)
• M8 hex nut (4x)
• Washer Ø 9 mm (8x)
Not included in the scope of delivery:
• Flat gasket Ø 7 mm (4x)
• Rubber base: 410 x 255 x 13 mm
The length of the screws to be used varies, depending on the
thickness of the table top.
WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
1.
The length of the screws to be used varies, depending on
the thickness of the table top.
2.
Mark the drill holes. Use the fretsaw as a template for
this purpose.
3.
Drill 4 holes with a diameter of 8 mm into the work table
and the rubber base.
4.
Screw the scroll saw onto the workbench with the hex-
agonal bolt (G) through the assembly points (fig. 3 pos.
19) in the following sequence (fig. 5):
A Fretsaw
B Rubber base
C Work table
D Flat gasket
E Washer
F Hex nut
5.
Tighten the hexagonal nut (F) first.

9. Assembly

WARNING
Danger of injury! Disconnect the mains plug on the scroll saw
before all assembly work.
9.1 Installing the depressor (fig. 6, 7)
NOTE:
Before assembling the depressor (24), the saw blade pre-in-
stalled at the factory (22) must be removed (see 9.3).
1.
Remove the saw blade (22) as described in 9.3.
2.
Remove the depressor (24) from the saw blade guard
(5) by loosening the screw (25) completely (see fig. 6).
3.
Insert the holder (4) into the opening (see fig. 7).
4.
Fasten the holder (4) with the knurled screw (3).
5.
Install the depressor (24). Insert the screw (25) into the
holder (4) and fasten it.
6.
Insert the saw blade (22) again as described in 9.3.
7.
Ensure that the depressor (24) does not contact the saw
blade (22).
The depressor (24) must always be adjusted according to
the workpiece height. However, the workpiece should not be
clamped, but should rather be able to move freely.
The depressor (24) is used to lock the workpiece so that it
cannot swing upwards, which would destroy the saw blade
(22).
9.2 Installing the blow-off device (fig. 8)
1.
Ensure that the saw blade guard (5) folded down.
2.
Screw the blow-off device (1) clockwise onto the holder
(2) as described in fig. 8.
9.3 Changing the saw blade (fig. 1, 8-11)
IMPORTANT
To avoid injuries attributed to inadvertent startup:
Before removing or replacing the saw blade, al-
ways press "0" and remove the mains plug from
the socket.
9.3.1 Removing the saw blade without pins (op-
tional)
1.
To remove the saw blade (22) , lift the table insert (26)
upwards.
2.
First, release the tension by flipping the tension lever (11)
upwards. Continue reducing the tension by turning clock-
wise as required.
3.
Press the support (12) down lightly (see fig. 9).
4.
Then loosen the upper saw blade clamping lever (28),
followed by the lower saw blade clamping lever (29) us-
ing the Allen key (23).
9.3.2 Inserting the saw blade without pins
(optional)
The teeth of the saw blade must always point downwards.
1.
First, secure the saw blade (22) in the lower saw blade
mounting (30). To secure the saw blade (22), tighten the
lower saw blade clamping screw (29) using the Allen
key (23).
2.
Press the support (12) down lightly. Fasten the other end
of the saw blade (22) in the top saw blade holder (27)
(see fig. 9).
3.
Fix the saw blade (22) with the upper blade clamping
screw (28) (see fig. 10).
GB
7

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis