Technical Data; Before Putting Into Operation; Attachment And Operation - Parkside 600 A1 Bedienungs- Und Sicherheitshinweise

• The use of incorrect or damaged mains cables can lead to
injuries caused by electricity.
• Even when all safety measures are taken, some remaining
hazards which are not yet evident may still be present.
• Remaining hazards can be minimized by following the in-
structions in „Safety Precautions", „Proper Use" and in the
entire operating manual.
• Before carrying out any adjustment or maintenance work,
switch off the device and disconnect the mains plug.

8. Technical data

AC motor
Power
Operating mode
Spindel speed
Max. workpiece length
Max. workpiece diameter
Headstock thread
Weight
Dimensions L x W x H mm
* Operating mode S1, continuous operation
Noise
Total vibration values determined in accordance with EN
61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection.
The effects of noise can cause a loss of hearing. Total vibration
values (vector sum - three directions) determined in accordance
with EN 61029.

9. Before putting into operation

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.
• Check the device and accessory parts for trans - port dam-
age.
• If possible, store the packaging until the warranty period has
expired.
ATTENTION
The device and packaging materials are not toys!
Children must not be allowed to play with plastic
bags, film and small parts! There is a risk of swal-
lowing and suffocation!
• The machine must be securely installed, i.e. bolted down on
a workbench, base frame or similar.
6 GB
220 - 240 V ~ 50Hz
550 Watt
S1 *
800 - 3000 min
-1
600 mm
25 cm
M 18 x 1,5
6,7 kg
1010x154x215
86,6 dB(A)
3 dB
99,6 dB(A)
3 dB
• Before the machine is put into operation, all covers and safe-
ty devices must be properly attached.
• In the case of wood which has already been worked with,
check for foreign bodies such as nails or screws etc.
• Before connecting the machine, check that the data on the
type plate matches those of the mains system.
• The machine must only be connected to a properly installed
safety socket which is protected by a fuse of at least 16A.

10. Attachment and operation

m Warning! Risk of injury!
Prepare the workplace where you intend to place the electrical
power tool. Provide enough space to ensure safe and trouble-
free operation. The power tool is designed for working in en-
closed rooms and has to be installed on level and firm ground.
m Important! Pull out the power plug before car-
rying out any maintenance, resetting or assembly
work on the device!
Fixation of the machine (Fig. 1)
Before operation, the device must be screwed to a workbench,
undercarriage or similar. Use the slotted holes (A) for this pur-
pose.
Installing the tool rest (Fig. 1; 4)
1. Fit the clamping lever for the tool rest (14) as shown in
figure 6.
1. Plug the tool rest (6) into the hole in the tool support (5).
2. Fasten the tool rest (6) at the desired height using the
locking screw (13).
Setting the tool rest (Fig. 1; 4)
1. The height of the tool rest (6) can be set by loosening the
locking screw (13).
2. In order to set the length of the tool rest (6), loosen the
clamping lever for tool rest (14). The tool rest (6) must
be driven as close as possible to the workpiece without
touching it.
3. Retighten the clamping lever for the tool rest (14).
Adjustment of the tailstock (Fig. 1; 5)
1. Loosen the clamping lever (11) for the tailstock (9) in or-
der to set the distance between the tailstock (9) and the
headstock drive centre (4).
2. To adjust the clamping pressure use the handwheel (10)
and secure it with the counternut (8).
Warning! Make sure that the tool rest (6) is tight-
ened securely and cannot turn in towards the
workpiece.
Securing the workpiece on the headstock drive
centre (Fig. 1)
1. Locate the centre of the workpiece by accurately draw-
ing diagonal lines on each end. The intersection point of
these two lines will indicate the centre of the workpiece.