Herunterladen Inhalt Inhalt Diese Seite drucken

Electrical Connection; Accessories; Maintenance - Parkside PKS 1500 A2 Bedienungs- Und Sicherheitshinweise

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 79
Switch ON / switch OFF the laser (Fig. 6)
To switch on: Move the ON/OFF (33) switch of the la-
ser (34) to the "1" position. A laser line is projected onto
the material you wish to process, providing an exact guide
for the cut.
To switch off: Move the ON/OFF switch of the laser to
the "0" position.
Adjusting the laser (Fig. 7)
If the laser (31) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (32) and set
the laser by moving sideways to that the laser beam strikes
the teeth of the saw blade (5).

11. Electrical connection

The electrical motor installed is connected and
ready for operation. The connection complies
with the applicable VDE and DIN provisions.
The customer's mains connection as well as the
extension cable used must also comply with
these regulations.
Important information
In the event of an overloading the motor will switch itself
off. After a cool-down period (time varies) the motor can
be switched back on again.
Damaged electrical connection cable
The insulation on electrical connection cables is often dam-
aged.
This may have the following causes:
• Passage points, where connection cables are passed
through windows or doors.
• Kinks where the connection cable has been improperly
fastened or routed.
• Places where the connection cables have been cut due
to being driven over.
• Insulation damage due to being ripped out of the wall
outlet.
• Cracks due to the insulation ageing.
Such damaged electrical connection cables must not be
used and are life-threatening due to the insulation damage.
Check the electrical connection cables for damage regu-
larly. Make sure that the connection cable does not hang
on the power network during the inspection.
Electrical connection cables must comply with the applica-
ble VDE and DIN provisions. Only use connection cables
with the marking „H 07 RN".
The printing of the type designation on the connection ca-
ble is mandatory.
AC motor
• The mains voltage must be 230 V ~
• Extension cables up to 25 m long must have a cross-sec-
tion of 1.5 mm
.
²
For single-phase AC motors, we recommend a fuse of C
16A or K 16A for machines with high starting current (from
3000 watts)!
Connections and repairs of electrical equipment may only
be carried out by an electrician.
Please provide the following information in the event of any
enquiries:
• Type of current for the motor
• Machine data - type plate
• Machine data - type plate

12. Accessories

SAW DUST EXTRACTION
The mitre saw is equipped with an extraction port to which
an extraction system can be connected. Alternatively, a dust
bag can also be attached.
The hose of the extraction system is fastened on the extrac-
tion port with a clamp. We recommend emptying the bag or
container from time to time and cleaning the filter.
The air speed of the suction system must be at least 30
metres per second.

13. Maintenance

If personnel qualified for unusual maintenance
tasks or repairs must be obtained during of after
the warranty period, please always contact a
service point recommended by us or contact the
manufacturer.
m Warning! Prior to any adjustment, maintenance or ser-
vice work disconnect the mains power plug!
• Only perform repair, maintenance and cleaning work
as well as the correction of malfunctions with the drive
switched off as a basic rule.
• All protective and safety equipment must be reassembled
immediately after repair, maintenance is completed.
NORMAL SERVICE TASKS
Normal service tasks can also be performed by untrained
personnel and are all described in the preceding sections
and in this chapter.
• The mitre saw must not be lubricated, because it always
cuts dry surfaces; all moving machine parts are self-
lubricating.
• In the event of service work, personal protective equip-
ment must always be work (protective goggles and
gloves).
• Remove saw dust and chips regularly by cleaning the
cutting zone and support surfaces.
We recommend using a suction tool or brush.
ATTENTION: Do not use compressed air!
Check the saw blade from time to time: If problems arise
with the blade, it must be ground by a specialist or re-
placed, depending on the condition.
DECOMMISSIONING OF THE MACHINE
After the machine is decommissioned it can be disposed of
with normal industrial waste.
GB/CY
9

Werbung

Inhaltsverzeichnis

Fehlerbehebung

loading

Inhaltsverzeichnis