Residual Risks; Technical Data - Parkside MPKZ 2000 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

13 Do not use any loose reducing rings or bushes for the
reducing of holes on saw blades.
14 Make sure that fixed reducer rings for securing the inser-
tion tool have the same diameter and have at least 1/3
of the cutting diameter.
15 Make sure that fixed reducer rings are parallel to each
other.
16 Handle insertion tool with caution. They are ideally stored
in the originally package or special containers. Wear
protective gloves in order to improve grip and to further
reduce the risk of injury.
17 Prior to the use of insertion tools, make sure that all protec-
tive devices are properly fastened.
18 Prior to use, make sure that the insertion tool meets the
technical requirements of this electric tool and is properly
fastened.
19 Only use the supplied saw blade for cutting wood, never
for the processing of metals.
20 Only use saw blade diameters in accordance with the
markings on the saw.
21 Use additional workpiece supports, if required for work-
piece stability.
22 Workpiece support extensions must always be secured
and used during work.
23 Replace table inserts when worn!
24 Avoid overheating of the saw teeth.
25 When sawing plastic, avoid melting of the plastic.
Use the appropriate saw blades for this purpose. Replace
damaged or worn saw blades immediately.
When the saw blade overheats, stop the machine. Allow
the saw blade to cool down before using the machine
again.
Attention: Laser radiation
Do not stare into the beam
Class 2 laser
Protect yourself and you environment from acci-
dents using suitable precautionary measures!
• Do not look directly into the laser beam with unprotected
eyes.
• Never look into the path of the beam.
• Never point the laser beam towards reflecting surfaces and
persons or animals. Even a laser beam with a low output
can cause damage to the eyes.
• Caution - methods other than those specified here can result
in dangerous radiation exposure.
• Never open the laser module. Unexpected exposure to the
beam can occur.
• If you do not use the device for a long time, the batteries
should be removed.
• The laser may not be replaced with a different type of laser.
• Repairs of the laser may only be carried out by the laser
manufacturer or an authorised representative.

Residual risks

The machine has been built according to the state
of the art and the recognised technical safety re-
quirements. However, individual residual risks can
arise during operation.
• Health hazard due to electrical power, with the use of im-
proper electrical connection cables.
• Furthermore, despite all precautions having been met, some
non-obvious residual risks may still remain.
• Residual risks can be minimised if the „safety instructions"
and the „Proper use" are observed along with the whole of
the operating instructions.
• Do not load the machine unnecessarily: excessive pressure
when sawing will quickly damage the saw blade, which re-
sults in reduced output of the machine in the processing and
in cut precision.
• When cutting plastic material, please always use clamps:
the parts which should be cut must always be fixed between
the clamps.
• Avoid accidental starting of the machine: the operating but-
ton may not be pressed when inserting the plug in an outlet.
• Use the tool that is recommended in this manual. In doing so,
your machine provides optimal performance.
• Hands may never enter the processing zone when the ma-
chine is in operation.
• Release the handle button and switch off the machine prior
to any operations.

6. Technical data

AC motor.....................................................220 - 240 V ~ 50Hz
Power S1* ..................................................................2000 Watt
Idle speed n
0
1 gear ........................................................................ 3200 min
st
2 gear ....................................................................... 4500 min
nd
Carbide saw blade ...............................ø 255 x ø 30 x 2,2 mm
Number of teeth .......................................................................48
Maximum tooth width of saw blade .................................. 3 mm
Swivel range .................................................. -45° / 0°/ +45°
Mitre cut ....................................................0° bis 45° to the left
Saw width at 90° ................................................. 340 x 90 mm
Saw width at 45° ................................................. 240 x 90 mm
Saw width at 2 x 45°
(double mitre cut) .................................................. 240 x 45 mm
Protection class .................................................................... II /
Weight ....................................................................... ca. 14,7 kg
Laser class ................................................................................... 2
Wavelength of laser ........................................................ 650 nm
Laser output .....................................................................< 1 mW
* S1 operating mode, continuous duty
The work piece must have a minimum height of 3
mm and a minimum width of 10 mm.
Make sure that the workpiece is always secured
with the clamping device.
-1
-1
GB/CY 7