Vitek VT-1480 GY Betriebsanweisung Seite 6

ENGLISH
•
Set the required operation speed 1-20 using
the control (1).
•
To switch the blender on press and hold the
button (2).
• When the button (3) is pressed, the unit oper-
ates at maximal rotation speed.
•
During operation hold the motor unit (4) with
one hand and the chopper bowl (12) with
another hand.
•
After you finish using the chopper, take the
plug out of the socket, disconnect the motor
unit (4) from the geared lid (10) by turning it
counterclockwise.
• Remove the geared lid (10) by turning it coun-
terclockwise.
•
Carefully remove the knife (11) taking it by the
upper plastic end.
•
Take the chopped products out of the chop-
per bowl (12).
•
Clean, wash and dry all the used parts imme-
diately after the end of operation.
• Put the knife (11) into a plastic protective
cover.
Attention!
Continuous operation time of the unit should not
exceed 20-30 seconds.
Follow the described sequence of operations
strictly.
USING THE CHOPPING KNIFE (26)
Attention!
Do not chop very hard products, such as nut-
–
megs, coffee beans and cereals.
Before you start chopping:
-
Remove bones, sinews and cartilage from
meat.
-
Cut meat, onion, garlic, carrot etc. into
approximately equal slices.
-
When chopping greens, remove stems of
herbs.
Chopping
Warning:
- Before assembling make sure that the power
plug is not inserted into the socket.
- Do not overload the processing bowl!
Caution: The blades are very sharp!
•
Set the driving shaft (27) on the axis of the
processing bowl (22).
VT-1480.indd 6
•
Remove the plastic protective cover from the
blades of the knife (26) and set the knife (26)
on the spline of the driving shaft (27).
•
Put the products into the processing bowl
(22).
• Put the geared lid (15) on the bowl (22).
• Press the clamp (21) and turn the geared lid
(15) counterclockwise to the position " ",
release the clamp (21) and check the fixation
of the geared lid (15).
•
Put the motor unit (4) on the geared lid (15)
and turn it clockwise until fixing.
•
Insert the plug into the socket.
• Set the required speed 1-20 using the con-
trol (1).
•
To switch the blender on press and hold the
button (2).
•
When the button (3) is pressed, the knife
rotates at maximal rotation speed.
•
During operation hold the motor unit (4) with
one hand and the bowl (22) with the other
hand.
•
After you finish using the unit, take the plug
out of the socket, disconnect the motor unit
(4) from the geared lid (15) by turning it coun-
terclockwise.
•
Then remove the geared lid (15) from the
bowl (22) by pressing the clamp (21) and
turning the lid (15) clockwise.
•
Carefully remove the knife (26) taking the
upper end of the driving shaft.
• Take the chopped products out of the pro-
cessing bowl (22).
•
Clean, wash and dry all the used parts imme-
diately after the end of operation.
•
Put the knife (26) into a plastic protective
cover.
Attention! Continuous operation time of the unit
should not exceed 20-30 seconds.
USING THE DISCS (SHREDDING/SLICING,
FRENCH FRIES, POTATO MUD)
• Set the driving shaft (27) on the axis of the
bowl (22).
•
Set the required disc (23, 24, 25) on the driv-
ing shaft (27).
•
Put the geared lid (15) on the bowl (22).
•
Press the clamp (21) and turn the geared lid
(15) counterclockwise to the position " ",
6
02.08.2012 15:15:40