Herunterladen Inhalt Inhalt Diese Seite drucken

Loading Saved Configurations; Loading Configuration Suggestions; Changing The Access Level; Locking The Unit, Changing A Password - Monacor DSM-26LAN Bedienungsanleitung

Digitales lautsprechermanagementsystem
Vorschau ausblenden Andere Handbücher für DSM-26LAN:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

5.4.2 Loading saved configurations

CAUTION Prior to loading a configuration, always check wheth-
er the configuration matches the arrangement of the
connected speakers . The DSM-... offers most flexible
configuration options: thus, it is, for example, possible
that an output configured to control a tweeter becomes the bass
frequency output in a different configuration; tweeters connected
to the output may then be overloaded .
To load a saved configuration:
1) Call up the menu item
Load: .
2) Use the rotary knob SELECT/ ENTER (7) to select a storage location
and press the knob to confirm .
3) The following message will appear on the display:
Load Preset ?
NO/yes
To cancel, press the rotary knob SELECT/ ENTER .
To continue loading, rotate the rotary knob SELECT/ ENTER so that
the following message appears on the display:
Load Preset ?
no/YES
Then press the knob .
While the preset is being loaded, the symbol
the preset name .

5.4.3 Loading configuration suggestions

It is possible to call up a few factory-set configuration suggestions .
Thus, specific channel links and signal assignments by means of the
function MIXER are preset and can be used as a basis for further
settings (example
 chapter 7 .13) .
1) Call up the menu item
Routing: .
2) Use the rotary knob SELECT/ ENTER (7) to select a configuration
suggestion .
3) Exit the system menu .

5.4.4 Changing the access level

To change the access level and thus to obtain other access rights
(
 chapter 5 .1), enter the appropriate password:
1) Enter the menu item
Access Level:
2) Use the rotary knob SELECT/ ENTER (7) to select the option
, then press the knob .
Unlocked
on the display .
3) Enter the password required:
– Use the rotary knob SELECT/ ENTER to select a character (upper-
case letter, lowercase letter, digit or special character) .
– Press the rotary knob to go to the next character .
– Use the button EXIT to go to the previous character position .
To delete the entire entry, go to the first character position and
press the button EXIT .
– Use the button MENU to confirm the final character of the pass-
word and to terminate the entry .
Note: To overwrite characters you may have accidentally entered at the end
of the password, use the blank character . It can be found after the
lowercase letters, following the character "}" .
When an incorrect password is entered, the following message will
appear on the display:
Access Level:
**** Locked ****
In this case, repeat steps 2 and 3, using the correct password .
will appear behind
*
.
will appear
Enter Password

5.4.5 Locking the unit, changing a password

With the steps described below, the unit will be set to the lowest
access level (Locked State) . In addition, it is possible to change the
password for the access level "User" .
1) Call up the menu item
Access Level:
2) Use
the
rotary
knob
, then press the knob .
**** Locked ****
will appear on the display .
3) Enter either the current password for the access level "User" or a
new password:
– Use the rotary knob SELECT/ENTER to select a character (upper-
case letter, lowercase letter, digit or special character) .
– Press the rotary knob to go to the next character .
– Use the button EXIT to go to the previous character position .
To delete the entire entry, go to the first character position and
press the button EXIT .
– Use the button MENU to confirm the final character of the pass-
word and to terminate the entry . Make sure to remember a new
password!
Note: The maximum length of the password is 8 characters . To overwrite
characters you may have accidentally entered at the end of the pass-
word, use the blank character . It can be found after the lowercase
letters, following the character "}" .
4)
will appear on the display . To confirm the
Confirm Password
password, press the button MENU again, or, to change the pass-
word again, press the button EXIT .
The unit is now locked (Locked State) . It can only be unlocked when
a correct password is entered (

5.4.6 Showing system information

1) Call up the menu item
Version Info
2) Use the rotary knob SELECT/ENTER (7) to select the information
to be shown:
= serial number
SN
= firmware version
FW
= hardware version
HW
= IP address
IP Address
= hardware address
MAC Address
.
SELECT/ ENTER
(7)
to
Set Password
 chapter 5 .4 .4) .
.
select
29

Werbung

Kapitel

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Dsm-48dtDsm-48lan

Inhaltsverzeichnis