Phase Reversal; Copying Settings; Muting Outputs; Functions Of The System Menu - Monacor DSM-26LAN Bedienungsanleitung

3) Set the threshold value
When this threshold value is exceeded, the gain will be reduced .
Note: To deactivate the limiter, set the threshold to its maximum value
(24 dBu) .
4) Set the release time
reach its original value after the signal has fallen below the thresh-
old value . The release time depends on the gain attenuation and
is specified in dB/s .

5.3.10 Phase reversal

The signal of an output channel can be inverted (phase reversal), e . g .
to correct a reverse polarity of speakers connected .
1) Select the channel to be set .
2) Call up the function
3) Select if the signal of this output is to be inverted (
not ( ) .
Normal

5.3.11 Copying settings

To copy the settings of a signal processing function to another channel:
1) Make or select the setting for a signal processing function of a
channel (e . g . limiter,
2) Press the button COPY (6) .
display as a confirmation .
3) Select the channel that is to adopt the setting .
Note: Make sure that the signal processing function selected at the target
channel is the same as the function selected at the source channel
while the setting was copied .
4) Press the button PASTE (8) . The following message will appear on
the display:
Paste Item?
Push to confirm
5) Press the rotary knob SELECT/ ENTER (7) to confirm .
6) If required, repeat steps 3 – 5 for any further channels that are to
adopt the setting .

5.3.12 Muting outputs

To mute an output, press the corresponding button MUTE (9) . When
an output is muted, the LED next to the respective button will light
up . To unmute an output, press the button again .

5.4 Functions of the system menu

The following general settings can be made by means of the system
menu (fig . 8) . Use the button MENU (4) to call up the menu and the
button EXIT (4) to exit the menu . Press the button MENU repeatedly
to select a menu item .
Load: 1 Basic
EX M
Save: 3 Empty
EX M
Access Level: Unlocked
M
EX M
Version Info
EX M
Routing: Stereo 1-Way
Fig. 8 Menu structure of the system menu
28
, i . e . the maximum output level .
Thr:
, i . e . the time it takes for the gain to
Rel.:
.
Phase
☞
chapter 5 .3 .9) .
will briefly appear on the
Copied
S E Load Preset? no/YES
S E Set Presetname:
E Enter Password
S
**** Locked ****
E
SN: 0000012345 S FW: 3.8.21.31781
S

5.4.1 Saving configurations

Unless a specific switch-on preset is defined (
settings made at the DSM-... will remain in force after switch-off . In
addition, it is possible to save various configurations as a "preset" at
the unit: The settings made by means of the menu for the inputs and
outputs as well as any muting of the outputs will be saved .
The configurations saved at the unit can also be used when the
DSM-... is operated by remote control from the computer (
ter 7 .3 .2 ., UNIT PRESETS) .
To save a preset:
1) Call up the menu item
2) Use the rotary knob SELECT/ ENTER (7) to select a storage location
and then press the button to confirm . If you do not want to over-
write a saved configuration, select a free storage location (
) or
Inverted
Set Presetname:
Note: Depending on the access rights of the current access level, the storage
function may be locked generally or for a defined storage location
range (
3) Enter a name for the preset or, if required, change the existing
name:
– Use the rotary knob SELECT/ ENTER to select a character (upper-
case letter, lowercase letter, digit or special character) .
– Press the rotary knob to go to the next character .
– Use the button EXIT to go to the previous character position .
To delete the entire entry, go to the first character position and
press the button EXIT .
– Use the button MENU to confirm the final character of the name
and to terminate the entry .
Note: To overwrite characters you may have accidentally entered at the end
of a preset name, use the blank character . It can be found after the
lowercase letters, following the character "}" .
4) The following message will appear on the display:
Save Preset ?
To save the preset, press the rotary knob SELECT/ ENTER .
To cancel, rotate the rotary knob SELECT/ ENTER so that the follow-
ing message appears on the display:
Save Preset ?
Then press the knob .
5) When the preset has been saved,
appear on the display .
S E
A Z 0 9 S E EX M Save Preset? no/YES
... ... ...
A Z 0 9 S E
... ... ...
Set Password A ... Z ... 0 ...
S HW: 4.9.3
.
Save:
will appear on the display .
☞ chapters 7 .4 and 7 .9) .
no/YES
NO/yes
S
EX M
EX Confirm Password M EX
9 S E M
S IP Address
169.254.45.229
M = MENU EX = EXIT
☞
chapter 7 .7), the
☞
chap-
) .
Empty
will briefly
Preset saved
E
S MAC Address S
B896:74:01:24:04
S = SELECT E = ENTER