Bestway 58304 Bedienungsanleitung Seite 2

AQUACLIMB AUTOMATIC POOL CLEANER
Automatic Pool Cleaner for Above Ground Pools
Cleans the bottom of your pool automatically. Works with all major brands of soft-wall pools.
Model 58304 includes 6.1m (20 ft.) of hose to fit pool sizes up to 4.85 m (16 ft).
The Automatic Pool Cleaner is a unique automatic above ground pool cleaner that is compatible with very small pumps as low as
3.8m /h (1,000 gal/h), and up to 9.5m /h (2,500 gal/h).
3 3
The Automatic Pool Cleaner is equipped with an adjustable pressure regulator. The regulator is preset in the factory for use with pumps
between 3.8m 3 /h (1,000 gal/h) and 5.7m
The Automatic Pool Cleaner has a built-in filter that prevents clogging of your hoses and filter system. Before connecting the Automatic
Pool Cleaner, inspect the unit to make sure the bottom plate is properly locked in position and that the mesh bag is clean.
WARNING!
THIS IS NOT A TOY!
- Do not let children use or play with the cleaner. Assemble and disassemble this product by adult only.
- Do not allow swimming in the pool while the cleaner is in use.
- TURN OFF THE PUMP before connecting cleaner to the pool.
- If there are stones, roots, or metal corrosion in contact with the bottom side of the liner, clean them out before installing the cleaner.
If necessary, have a qualified professional do the cleaning.
- If the liner is brittle, damaged or wrinkled, have a qualified professional perform the necessary repairs or liner replacement before
installing the cleaner.
- Make sure the cleaner is not in the pool during any chemical sanitization.
- TURN OFF THE PUMP before servicing the cleaner or performing any maintenance.
NOTE: Drawings for illustration purpose only. May not reflect actual product. Not to scale.
SAVE THESE INSTRUCTIONS
Parts Reference Overview
HOW TO CONNECT YOUR Automatic Pool Cleaner
Note: Turn filtration OFF before connecting the Automatic Pool Cleaner to your pool.
The 3 connectors (F2/F3/F4) and Connection Hose A enables the Automatic Pool Cleaner to fit most brands of Above Ground Pools in
the market. Choose the right connector and see the following diagrams for proper connection to the water outlet of your pool.
Φ32mm (1.25in.) Strainer
Detach the strainer plug and insert the F4 into the strainer hole.
Φ92mm (3.6 in.) Strainer (with side thread)
Screw F2 onto F3, and then align and screw F3 onto the strainer.
Hose Section Assembly
Connect A to B, then to E to D (6 times), and then to C. Lastly, connect the spare end of A to the connector F (F2 or F4).
For 4.57m (15 ft.) & 4.85m (16 ft.) round & rectangular pools, connect all 6 long hoses (E) and 6 short hoses (D).
For pools smaller than 4.57m (15 ft.), reduce the number of
long hoses (E) and short hoses (D) simultaneously until total
length of hose assembly is equivalent to the length from
skimmer/dedicated suction line to the fastest point in the
pool plus a length equal to hoses E+D. (Fig. 1)
Fig.1
3 /h (1,500 gal/h).
Φ38mm (1.5in.) Strainer
F4
F3
F2
Completely immerse the hoses and the Automatic Pool
Cleaner to let air escape, then connect the open end of the
hose to the Automatic Pool Cleaner (Fig. 2).
Fig.2
F2
Φ80mm (3 in.) Strainer
Unscrew the strainer grid cover and screw F2 into the middle thread of the strainer.
F2
TIPS: Immerse the hoses into water one by one in correct
sequence to remove air and finish hose connection under the
water. Alternately, you can connect all hoses together and place
either opening end towards the pool water inlet hole to let water
flow into to push out the entrapped air. Trapped air in your
cleaning system may prevent the pump from operating correctly.
If this happens, switch off your pump, open the release valve (if
applicable) on your filter and let air escape until only water
comes out from release valve. Then close the valve. Refer to
your filtration manual for how to release the air.
2
F4
Φ36mm (1.4 in.) Strainer Hole
Remove the grid cover and directly insert the
cuff of hose A into the strainer hole.
F2
S-S-005147