Transport; Maintenance; Storage - Parkside PKZS 2000 A1 Bedienungs- Und Sicherheitshinweise

• Use the handle (1) to tilt the machine head (4) to the left
until it coincides with the required angle value (in this con-
nection see also section 8.6).
• Re- tighten the fixing screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (Fig. 3/14)
• The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the knurled nut on the screw (24).
Move the stop for the cutting depth limitre (25) to the out-
side. Turn the screw (24) in or out to set the required cutting
depth. Then re- tighten the knurled nut on the screw (24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (Fig. 1/22)
The saw is equipped with a debris bag (17) for sawdust and
chips.
Squeeze together the metal ring on the dust bag and attach
it to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper
at the bottom.
8.10 Changing the saw blade (Fig. 1/2/15-18)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and lock with the
safety pin (23).
• Press the release lever (3). Swing up the saw blade guard
(5) to the point where the recess in the saw blade guard
(5) is above the flange bolt (29).
• With one hand insert the allen key (d) in the flange bolt
(29).
• Hold the Allen key (d) and slowly close the saw blade
guard (5) until it touches the Allen key (d).
• Firmly press the saw shaft lock (31) and slowly rotate
the flange bolt (29) in clockwise direction. The saw
shaft lock (31) engages after no more than one rotation.
Attention! When loosening the screw, the machine head
lowers slightly.
• Now, using a little more force, slacken the flange bolt (29)
in the clockwise direction.
• Turn the flange screw (29) right out and remove the exter-
nal flange (30).
• Take the blade (6) off the inner flange (32) and pull out
downwards.
• Carefully clean the flange screw (29), outer flange (30)
and inner flange (32).
• Fit and fasten the new saw blade (6) in reverse order.
• Important! The cutting angle of the teeth, in other words
the direction of rotation of the saw blade (6) must coincide
with the direction of the arrow on the housing.
• Before continuing your work make sure that all safety de-
vices are in good working condition.
• Important! Every time that you change the saw blade (6),
check to see that it spins freely in the table insert (10) in
both perpendicular and 45° angle settings.
• Important! The work to change and align the saw blade
(6) must be carried out correctly.
48 GB/MT
8.11 Using the laser (Fig. 3/19/20)
• To switch on: Move the ON/OFF switch of the laser (34)
to the "1" position. A laser line is projected onto the mate-
rial you wish to process, providing an exact guide for the
cut.
• To switch off: Move the ON/OFF switch of the laser (34)
to the "0" position.
8.12 Adjusting the laser (Fig. 20)
If the laser (33) ceases to indicate the correct cutting line,
you can readjust the laser. To do so, open the screws (e)
and set the laser by moving sideways to that the laser beam
strikes the teeth of the saw blade (6).

9. Transport

• Tighten the set screw (26) in order to lock the rotary table
(14)
• Activate the release lever (3), press the machine head (4)
downwards and secure with the safety pin (23). The saw is
now locked in its bottom position.
• Fix the saw's drag function with the locking screw for drag
guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as described
under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or ser-
vice work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time using
a cloth. In order to extend the service life of the tool, oil the
rotary parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
Brush inspection
Check the carbon brushes after the first 50 operating hours
with a new machine, or when new brushes have been fitted.
After carrying out the first check, repeat the check every 10
operating hours.
If the carbon is worn to a length of 6 mm, or if the spring
or contact wire are burned or damaged, it is necessary to
replace both brushes. If the brushes are found to be usable
following removal, it is possible to reinstall them.
When servicing the carbon brushes, open the two latches
counterclockwise (as shown in Figure 21). Then remove the
carbon brushes.
Replace the carbon brushes in the reverse order.

11. Storage

Store the device and its accessories in a dark, dry and frost-
proof place that is inaccessible to children. The optimum stor-
age temperature is between 5 and 30˚C.
Store the electrical tool in its original packaging.
Cover the electrical tool in order to protect it from dust and
moisture.