Herunterladen Inhalt Inhalt Diese Seite drucken

Transport; Maintenance - Parkside PZKS 2000 A1 Bedienungs- Und Sicherheitshinweise

Kapp- und zugsäge
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 62
Attention! For mitre cuts (inclined saw head), the left side of
the moveable stop rails (16a) must be fixed in the outer position.
• Open the set screw (16b) for the moveable stop rail (16a)
and push the moveable stop rail (16a) outwards.
• The moveable stop rail (16a) must be fixed far enough in
front of the innermost position that the distance between the
stop rail (16a) and the saw blade (6) amounts to a minimum
of 8 mm.
• Before making a cut, check that the stop rail (16a) and the
saw blade (6) cannot collide.
• Re-tighten the set screw (16b).
• Move the machine head (4) to its upper position.
• Release the rotary table (14) by loosening the handle (11).
• Using the handle (11), set the rotary table (14) to the de-
sired angle (refer also to point 8.4 in this regard).
• Re-tighten the handle (11) to secure the rotary table (14).
• Undo the set screw (22).
• Use the handle (1) to tilt the machine head (4) to the left until
it coincides with the required angle value (in this connection
see also section 8.6).
• Re-tighten the set screw (22).
• Cut as described under section 8.3.
8.8 Limiting the cutting depth (fig. 3/13)
• The cutting depth can be infinitely adjusted using the screw
(24). To do this loosen the knurled nut (24a) on the screw
(24). Turn the screw (24) in or out to set the required cutting
depth. Then re-tighten the knurled nut (24a) on the screw
(24).
• Check the setting by completing a test cut.
8.9 Sawdust bag (fig. 1/22)
The saw is equipped with a debris bag (17) for sawdust and chips.
Squeeze together the metal ring on the dust bag and attach it
to the outlet opening in the motor area.
The debris bag (17) can be emptied by means of a zipper at
the bottom.
Connection to an external dust extractor
For dust extraction, a vacuum hose can also be connected to
the dust extraction spout.
• Connect the vacuum hose with the dust extraction spout.
• The industrial vacuum cleaner must be suitable for the
material being worked.
• When vacuuming dust that is especially detrimental to health
or carcinogenic, use a special vacuum cleaner.
8.10 Changing the saw blade (fig. 1/2/14-17)
Remove the power plug!
Important!
Wear safety gloves when changing the saw blade.
Risk of injury!
• Swing the machine head (4) upwards and lock with the lock-
ing bolt (23).
• Loosen the retaining screw (5a) of the cover using a Philips
screwdriver.
WARNING! Do not fully remove this screw.
• Fold the saw blade guard (5) upwards until the saw blade
guard (5) is above the flange screw (28).
• With one hand insert the Allen key (C) in the flange screw
(29).
• Hold the Allen key (C) and slowly close the saw blade guard
(5) until it touches the Allen key (C).
• Firmly press the saw shaft lock (30) and slowly rotate the
flange screw (28) in clockwise direction. The saw shaft lock
(30) engages after no more than one rotation.
• Now, using a little more force, slacken the flange screw (29)
in the clockwise direction.
• Turn the flange screw (28) right out and remove the outer
flange (29).
• Take the blade (6) off the inner flange (31) and pull out
downwards.
• Carefully clean the flange screw (28), outer flange (29) and
inner flange (32).
• Fit and fasten the new saw blade (6) in reverse order.
• Important! The cutting angle of the teeth, in other words the
direction of rotation of the saw blade (6) must coincide with
the direction of the arrow on the housing.
• Before continuing your work make sure that all safety de-
vices are in good working condition.
• Important! Every time that you change the saw blade (6),
check to see that it spins freely in the table insert (10) in both
perpendicular and 45° angle settings.
• Important! The work to change and align the saw blade (6)
must be carried out correctly.
8.11 Using the laser (fig. 18)
• To switch on: Press the ON/OFF switch laser (33) 1x. A
laser line is projected onto the material you wish to process,
providing an exact guide for the cut.
• To switch off: Press again the ON/OFF switch laser (33).
8.12 Adjusting the laser (fig. 19-20)
If the laser (32) ceases to indicate the correct cutting line, you
can readjust the laser. To do so, open the screws (32b) and
remove the front cover (32a). Loosen the Philips head screws
(E) and set the laser by moving sideways until the laser beam
strikes the teeth of the saw blade (6).
After adjusting and tightening the laser, mount the front cover
by tightening both screws (32b) by hand.

9. Transport

• Tighten the handle (11) to lock the rotary table.
• Press the machine head (4) downwards and secure with the
locking bolt (23).
• Fix the saw's drag function with the locking screw for drag
guide (20) in rear position.
• Carry the equipment by the fixed saw table (15).
• When reassembling the equipment proceed as described
under section 7.

10. Maintenance

m Warning! Prior to any adjustment, maintenance or service
work disconnect the mains power plug!
General maintenance measures
Wipe chips and dust off the machine from time to time using a
cloth. In order to extend the service life of the tool, oil the rotary
parts once monthly. Do not oil the motor.
When cleaning the plastic do not use corrosive products.
GB/MT
53

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

Mpkz 2000 a1

Inhaltsverzeichnis