Disposal And Recycling; Transport - Parkside PKO 500 A2 Bedienungs- Und Sicherheitshinweise

Oil change: we recommend SAE 15W 40 or equivalent. The
original oil filling must be changed after 100 hours in opera-
tion; thereafter the oil must be drained and replaced with
new oil after every 500 hours in operation.
10.5 Changing the oil (Fig. 1,10,11)
Switch off the engine and pull the mains plug out of the sock-
et. Remove the oil sealing plug (16). After releasing any air
pressure you can unscrew the oil drain plug (12) from the
compressor pump (13).
To prevent the oil from running out in an uncontrolled
manner, hold a small metal chute under the opening and
collect the oil in a vessel. If the oil does not drain out com-
pletely, we recommend tilting the compressor slightly.
When the oil has drained out, re-fit the oil drain plug (12).
Dispose of the old oil at a drop-off point for old oil.
To fill in the correct quantity of oil, make sure that the com-
pressor stands on an even surface. Fill new oil through the
oil filler opening (20) until it comes up to the maximum level.
This is marked with a red dot on the oil level window (18)
(Fig. 11). Do not exceed the maximum filling quantity. Over-
filling the equipment may result in damage. Reinsert the oil
sealing plug (16) into the oil filler opening (20).
10.6 Cleaning the intake filter (Fig. 3, 12, 13)
The intake filter prevents dust and dirt being drawn in. It is
essential to clean this filter after at least every 300 hours in
service. A clogged intake filter will decrease the compres-
sor's performance dramatically. Open the thumb screw (E)
to the remove the intake filter.
Then pull off the filter cover (C). Now you can remove the
air filter (F) and the filter housing (D). Carefully tap out the
air filter, filter cover and filter housing. Then blow out these
parts with compressed air (approx. 3 bar) and reinstall in
reverse order.
10.7 Storage
m Important!
Pull out the mains plug and ventilate the equipment
and all connected pneumatic tools. Switch off the com-
pressor and make sure that it is secured in such a way
that it cannot be started up again by any unauthorized
person.
m Important!
Store the compressor only in a dry location which is
not accessible to unauthorized persons. Always store
upright, never tilted! Oil may leak out!
10.7.1 Releasing excess pressure
Release the excess pressure by switching off the compressor
and using the compressed air which is still left in the pressure
vessel, e.g. with a compressed air tool running in idle mode
or with a blow-out pistol.
40 GB/MT

11. Disposal and recycling

The equipment is supplied in packaging to prevent it from
being damaged in transit. The raw materials in this packag-
ing can be reused or recycled. The equipment and its acces-
sories are made of various types of material, such as metal
and plastic. Defective components must be disposed of as
special waste. Ask your dealer or your local council.
The packaging is wholly composed of environment-
ally-friendly materials that can be disposed of at a
local recycling centre.
Contact your local refuse disposal authority for more
details of how to dispose of your worn out electrical
devices.
Old devices must not be disposed of with household
waste!
This symbol indicates that this product must not be
disposed of together with domestic waste in
compliance with the Directive (2012/19/EU)
pertaining to waste electrical and electronic equipment
(WEEE). This product must be disposed of at a designated
collection point. This can occur, for example, by handing it in
at an authorised collecting point for the recycling of waste
electrical and electronic equipment. Improper handling of
waste equipment may have negative consequences for the
environment and human health due to potentially hazardous
substances that are often contained in electrical and
electronic equipment. By properly disposing of this product,
you are also contributing to the effective use of natural
resources. You can obtain information on collection points
for waste equipment from your municipal administration,
public waste disposal authority, an authorised body for the
disposal of waste electrical and electronic equipment or
your waste disposal company.

12. Transport

Use the handle to transport the compressor.
Observe the weight when lifting the compressor (see Techni-
cal Data).
When transporting the compressor in a motor vehicle, en-
sure good load securing.