Herunterladen Inhalt Inhalt Diese Seite drucken

Intended Use; General Safety Information - Parkside PBS 350 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für PBS 350 A1:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1
• Check the device and accessory parts for transport dam-
age.
• If possible, store the packaging until the warranty period
has expired.
ATTENTION!
The device and packaging materials are not toys! Children
must not be allowed to play with plastic bags, film and small
parts! There is a risk of swallowing and suffocation!
• Bandsaw / Bandsaw blade (pre-assembled)
• Saw table
• Push stick
• Parallel stop
• Open-ended spanner, size 10/13
• Allen key, size 3/4/5
• Screwdriver
• Original operating instructions

4. Intended use

The bandsaw is designed to perform longitudinal and cross
cuts on timber or wood-type materials. To cut round materi-
als you must use suitable holding devices.
The equipment is to be used only for its prescribed purpose.
Any other use is deemed to be a case of misuse. The user /
operator and not the manufacturer will be liable for any dam-
age or injuries of any kind caused as a result of this.
The machine is to be operated only with suitable saw blades.
To use the machine properly you must also o serve the safety
regulations, the assembly instructions and the operating in-
structions to be found in this manual.
All persons who use and service the machine have to be ac-
quainted with this manual and must be informed about the
machine's potential hazards. It is also imperative to observe
the accident prevention regulations in force in your area. The
same applies for the general rules of occupational health
and safety.
The manufacturer shall not be liable for any changes made to
the machine nor for any damage resulting from such changes.
Even when the machine is used as prescribed it is still impos-
sible to eliminate certain residual risk factors. The following
hazards may arise in connection with the machine's construc-
tion and design:
• Damage to hearing if ear-muffs are not used as necessary.
• Harmful emissions of wood dust when used in closed
rooms.
• Contact with the blade in the uncovered cutting zone.
• Injuries (cuts) when changing the blade.
• Injury from catapulted workpieces or parts of workpieces.
• Crushed fingers.
• Kickback.
• Tilting of the workpiece due to inadequate support.
• Touching the blade.
• Catapulting of pieces of timber and workpieces.
Please note that our equipment has not been designed for use
in commercial, trade or industrial applications. Our warranty
will be voided if the machine is used in commercial, trade or
industrial businesses or for equivalent purposes.

5. General safety information

Attention! The following basic safety measures must be ob-
served when using electric tools for protection against electric
shock, and the risk of injury and fire. Read all these notices
before using the electric tool and keep the safety instructions
for later reference.
Safe work
1 Keep the work area orderly
– Disorder in the work area can lead to accidents.
2 Take environmental influences into account
– Do not expose electric tools to rain.
– Do not use electric tools in a damp or wet environment.
– Make sure that the work area is well-illuminated.
– Do not use electric tools where there is a risk of fire or
explosion.
3 Protect yourself from electric shock
– Avoid physical contact with earthed parts (e.g. pipes,
radiators, electric ranges, cooling units).
4 Keep children away
– Do not allow other persons to touch the equipment or
cable, keep them away from your work area.
5 Securely store unused electric tools
– Unused electric tools should be stored in a dry, elevated
or closed location out of the reach of children.
6 Do not overload your electric tool
– They work better and more safely in the specified output
range.
7 Use the correct electric tool
– Do not use low-output electric tools for heavy work.
– Do not use the electric tool for purposes for which it is
not intended. For example, do not use handheld circular
saws for the cutting of branches or logs.
– Do not use the electric tool to cut firewood.
8 Wear suitable clothing
– Do not wear wide clothing or jewellery, which can be-
come entangled in moving parts.
– When working outdoors, anti-slip footwear is recommended.
– Tie long hair back in a hair net.
9 Use protective equipment
– Wear protective goggles.
– Wear a mask when carrying out dust-creating work.
10 Connect the dust extraction device if you will be process-
ing wood, materials similar to wood, or plastics.
– If connections for dust extraction and a collecting de-
vice are present, make sure that they are connected
and used properly.
– When processing wood, materials similar to wood, and
plastics. Operation in enclosed spaces is only permit-
ted with the use of a suitable extraction system.
11 Do not use the cable for purposes for which it is not
intended
— Do not use the cable to pull the plug out of the outlet.
Protect the cable from heat, oil and sharp edges.
12 Secure the workpiece
– Use the clamping devices or a vice to hold the work-
piece in place. In this manner, it is held more securely
than with your hand.
GB/IE
15

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis