Introduction; Device Description; Scope Of Delivery - Parkside PBS 350 A1 Bedienungs- Und Sicherheitshinweise Originalbetriebsanleitung

1. Introduction

Manufacturer:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
Dear Customer,
We hope your new tool brings you much enjoyment and suc-
cess.
Note:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified,
• A breakdown of the electrical system that occurs due to
the non-compliance of the electric regulations and VDE
regulations 0100, DIN 57113 / VDE0113.
We recommend:
Read through the complete text in the operating instructions
before installing and commissioning the device. The operating
instructions are intended to help the user to become familiar
with the machine and take advantage of its application pos-
sibilities in accordance with the recommendations. The op-
erating instructions contain important information on how to
operate the machine safely, professionally and economically,
how to avoid danger, costly repairs, reduce downtimes and
how to increase reliability and service life of the machine.
In addition to the safety regulations in the operating instruc-
tions, you have to meet the applicable regulations that apply
for the operation of the machine in your country. Keep the op-
erating instructions package with the machine at all times and
store it in a plastic cover to protect it from dirt and moisture.
Read the instruction manual each time before operating the
machine and carefully follow its information. The machine can
only be operated by persons who were instructed concerning
the operation of the machine and who are informed about the
associated dangers. The minimum age requirement must be
complied with. In addition to the safety requirements in these
operating instructions and your country's applicable regula-
tions, you should observe the generally recognized technical
rules concerning the operation of woodworking machines.
We cannot accept any liability for damage or accidents
which arise due to a failure to follow these instructions and
the safety instructions.
14 GB/IE
2. Device description (Fig. 1-16)
1. Clamping screw
2. Top saw band roller
3. Rubber surface
4. Saw band guard
5. Top saw band guide
6. Table insert
7. Saw table
8. Bottom saw band roller
9. Foot
10. Cover locking mechanism
11. Side cover
12. On/off switch
13. Locking screw for top saw band roller
14. Set screw for top saw band roller
15. Machine frame
16. Mains cable
17. Degree scale for swivel range
18. Motor
19. Extraction nozzle
20. Locking handle for saw table
21. Bandsaw blade
22. Adjustment handle for saw band guide
23. Locking handle for saw band guide
24. Parallel stop
25. Clamping bar for parallel stop
26. Push stick
27. 3 mm Allen key
28. 4 mm Allen key
29. Screwdriver
30. Open-ended spanner
31. Wing nut
32. Clamping plate
33. Knurled nut
34. U-reinforcement
35. Allen screw for top support bearing
36. Top support bearing
37. Top guide pin
38. Allen screw for top guide pins
39. Retainer (top)
40. Allen screw top retainer (2x)
41. Allen screw bottom support bearing
42. Bottom support bearing
43. Screw bottom retainer
44. Saw band protection
45. Allen screw for bottom guide pins
46. Bottom guide pin
47. Retainer (bottom)
48. Push Stick retainer
49. Screw (saw table adjustment)
50. Nut (saw table adjustment)
51. 5 mm Allen key

3. Scope of delivery

• Open the packaging and remove the device carefully.
• Remove the packaging material as well as the packaging
and transport bracing (if available).
• Check that the delivery is complete.