Introduction; Device Description (Fig. 1-2); Scope Of Delivery (Fig. 2); Intended Use - Parkside PUG 1600 A1 Bedienungs- Und Sicherheitshinweise

1. Introduction

MANUFACTURER:
scheppach
Fabrikation von Holzbearbeitungsmaschinen GmbH
Günzburger Straße 69
D-89335 Ichenhausen
DEAR CUSTOMER,
we hope your new tool brings you much enjoyment and suc-
cess.
NOTE:
According to the applicable product liability laws, the manu-
facturer of the device does not assume liability for damages
to the product or damages caused by the product that occurs
due to:
• Improper handling,
• Non-compliance of the operating instructions,
• Repairs by third parties, not by authorized service techni-
cians,
• Installation and replacement of non-original spare parts,
• Application other than specified.
We recommend:
Read through the complete text in the operating instructions be-
fore installing and commissioning the device.
The operating instructions are intended to help the user to be-
come familiar with the device and take advantage of its appli-
cation possibilities in accordance with the recommendations.
The operating instructions contain important information on
how to operate the device safely, professionally and economi-
cally, how to avoid danger, costly repairs, reduce downtimes
and how to increase reliability and service life of the machine.
In addition to the safety instructions in these operating instruc-
tions and the safety instructions for the machine mounted, you
must also observe your country's regulations applicable to the
operation of this device and the electric power tool mounted.
Keep the operating instructions package with the device at all
times and store it in a plastic cover to protect it from dirt and
moisture. Read the instruction manual each time before operat-
ing the device and carefully follow its information.
The device can only be operated by persons who were in-
structed concerning the operation of the machine and who are
informed about the associated dangers.
m Attention
The electric power tool mounted on the universal tool stand
may only be used by personnel who have been trained in the
use of the electric power tool and who have been instructed
with respect to the associated hazards.
The minimum age requirement must be complied with.
In addition to the safety instructions in this operating manual
and the separate regulations of your country, the generally
recognised technical rules relating to the operation of such de-
vices must also be observed.
We accept no liability for damage or accidents which arise
due to non-observance of these instructions and the safety in-
formation.
2 GB/CY

2. Device description (fig. 1-2)

A. Universal tool stand
B. Support arm
C. Crossbar
D. Adjustable workpiece support
E. Screw
F. Screw
G. Washer
H. Spring washer
I. Nut
J. Star-grip screw (small)
K. Star-grip screw (large)

3. Scope of delivery (fig. 2)

1x Universal tool stand (A)
2x Support arm (B)
2x Crossbar (C)
2x Adjustable workpiece support (D)
4x Screw M6x16 (E)
4x Screw M6x60 (F)
8x Washer 6mm (G)
8x Spring washer 6mm (H)
8x Nut M6 (I)
4x Star-grip screw (small) (J)
2x Star-grip screw (large) (K)

4. Intended use

Always observe the proper use of your universal tool stand.
The universal tool stand is designed for use with tabletop de-
vices such as mitre saws, scroll saws, circular table saws, etc.
Electric power tools without suitable mounting holes are not
permitted to be fitted to the universal tool stand and shall not
be operated in conjunction with the universal tool stand.
Electric power tools must be firmly bolted to the universal tool
stand before starting them up.
The universal tool stand is also designed as a workpiece sup-
port when working with mitre saws, scroll saws, circular table
saws, and other similar electric power tools.
The maximum workpiece length is 3 m.
Additional workpiece supports may have to be used (e.g. a
roller trestle) in order to prevent longer workpieces tilting.
Attention: Ensure that the workpiece support is secure and not
tilted!
Do not use the universal tool stand as a ladder or as scaffold-
ing. Ensure that all handgrips, nuts and screws are tightened
before use. Electric power tools on this device shall not exceed
an overall height of 152 cm. The maximum payload is 200
kg. Ensure that the universal tool stand is on a level, firm and
stable floor.
Any use beyond this is improper use. The manufacturer is not
responsible for the resultant damages, the user bears this risk
alone.