Operation; Maintenance; Storage And Winterization - Bestway 58259 Benutzerhandbuch

Operation

NOTE: Check the pool for correct installation and make sure both the pool's
Inlet and Outlet Valves are fully covered with water before operating the Filter
Pump or Sand Filter with the Pool Heater. Make sure that the Pool Heater and
Filter Pump or Sand Filter are correctly connected.
1. Start the Filter Pump or Sand Filter according to the owner's manual.
2. With the pump operating, insert the plug of the Pool Heater into a socket,
after test PRCD . The LED will light up for 0.5 seconds with a "beep"
sound, and the LED displays
3. Press the "POWER" button for 2 seconds, the LED turns on and the heater
starts to work, the LED display
4. Press the "POWER" button for 2 seconds again, the Pool Heater will turn
off.
NOTE: When the water temperature reach the set temperature, the LED
turns green.
NOTE: Never plug in the Pool Heater until the Filter Pump or Sand Filter has
been plugged in.
WARNING: To prevent the risk of electrical shock, ensure your hands are
completely dry when plugging-in the Filter Pump or Sand Filter and the Pool
Heater.
NOTE: To prevent the risk of electrical shock, never run the Filter Pump or
Sand Filter and the Pool Heater when people are in the pool.
NOTE: Do not dry run the Pool Heater. Damage caused by dry running the
Pool Heater is not covered by the manufacturer's warranty.
5. Remember to disconnect the Pool Heater first. Never unplug the Filter
Pump or Sand Filter when the Pool Heater is running.
6. Unplug the Filter Pump or Sand Filter and enjoy warm pool water!
OPERATING TIME TABLE
(Bestway Above Ground Pools)
2.44m x 66cm (8' x 26")
2.74m x 76cm (9' x 30'')
3.05m x 76cm (10' x 30")
3.66m x 76cm (12' x 30")
Fast Set Pools
TM
3.66m x 91cm (12' x 36")
4.57m x 91cm (15' x 36")
4.57m x 1.07m (15' x 42")
4.57m x 1.22m (15' x 48")
4.88m x 3.05m x 1.07m (16' x 10' x 42")
Steel Pro Oval Pools 5.49m x 3.66m x 1.22m (18' x 12' x 48")
TM
6.10m x 3.66m x 1.22m (20' x 12' x 48")
2.44m x 51cm (8' x 20")
2.44m x 61cm (8' x 24")
3.05m x 76cm (10' x 30")
3.05m x 1.00m (10' x 39.5")
3.30m x 1.02m (130" x 40")
Round
3.66m x 76cm (12' x 30")
Frame Pools
3.66m x 1.00m (12' x 39.5")
3.66m x 1.22m (12' x 48")
4.27m x 1.22m (14' x 48")
4.57m x 91cm (15' x 36")
4.57m x 1.22m (15' x 48")
2.87m x 2.01m x 1.00m (113" x 79" x 39.5")
3.00m x 2.01m x 66cm (118" x 79" x 26")
Rectangular Frame Pools
4.00m x 2.11m x 81cm (157" x 83" x 32")
4.04m x 2.01m x 1.00m (159" x 79" x 39.5")
4.12m x 2.01m x 1.22m (162" x 79" x 48")
Hydrium Oval Pool
4.88m x 3.66m x 1.22m (16' x 12' x 48'')
3.66m x 1.22m (12' x 48'')
Hydrium Pool
Hydrium Pool 3.05m x 1.22m (10' x 48'')
Notice:
• The table above is for reference only. Data are relevant for a covered pool with water at 25 degrees
Celsius on a clear day.
• Ambient air and water temperature has an effect on water heating efficiency.
.
.
Pool Size

Maintenance

CAUTION: YOU MUST UNPLUG THE POOL HEATER FIRST, THEN
UNPLUG THE FILTER PUMP OR SAND FILTER BEFORE PREFORMING
MAINTENANCE OR SEVERE RISK OF INJURY OR DEATH EXISTS.
1. Stop Water Flowing to the Filter Pump or Sand Filter and the Pool Heater:
a) Disconnect the Pool Heater and THEN the Filter Pump or Sand Filter.
b) Loosen the Hose Clamps on the pool's Inlet and Outlet Hoses.
c) Replace the Debris Screens with the Stopper Plugs in the pool's Inlet
and Outlet Valves.
d) Refer to the Filter Pump or Sand Filter 's Owner's Manual for information
on Filter Pump or Sand Filter maintenance.
2. After Filter Pump or Sand Filter maintenance, replace the Stopper Plugs
with the Debris Screens in the pool's Inlet and Outlet Valves. Water will now
flow to the Filter Pump or Sand Filter and the Pool Heater.
3. Operate as outlined in the Operation section of this manual.

Storage and Winterization

CAUTION: YOU MUST UNPLUG THE POOL HEATER AND THE FILTER
PUMP OR SAND FILTER BEFORE MAINTENANCE BEGINS OR SEVERE
RISK OF INJURY OR DEATH EXISTS.
To avoid damage, pool equipment must be winterized when temperatures are
lower than 4°C (40°F). Allowing water to freeze will damage the Pool Heater
and void the warranty.
NOTE: Do not leave the heater out in the open air for long periods of time.
When it is not in use, please clean and dry it and then store it in a cool, dry
place.
1. Follow the instructions previously outline to stop water flowing to the Filter
Pump or Sand Filter and the Pool Heater.
2. Detach all hoses.
3. Drain any water in the Pool Heater and clean all components thoroughly.
4. Put the Pool Heater in a cool, dry place, out of children's reach.
Time to increase by 1
degree Celsius
Hours
1.4
2.2
2.2
2.9
3.6
6.5
7.0
9.0
6.5
10.0
10.0
1.0
1.0
2.6
3.6
3.6
3.6
6.0
6.5
10.0
7.0
10.0
2.6
2.2
3.0
4.0
6.0
10.0
6.5
4.0
7
Water capacity Time to
(Calculated at 90% for Frame increase by
Pool and 80% for Fast Set &
Oval Pool)
Gallons Liters
500 1,890
1,000 3,750
1,500 5,680
2,000 7,500
2,500 9,460
3,000 11,350
3,500 13,250
4,500 17,035
1 degree
Celsius
Hours
1.0
2.5
3.0
4.0
6.0
7.0
8.0
10.0
S-S-004678 S-S-004678