Herunterladen Inhalt Inhalt Diese Seite drucken

Cutting With Angle; Cutting With Rip Fence; After Use; Cleaning And Care - Parkside PHKSAP 20-Li A1 Bedienungs- Und Sicherheitshinweise

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Cutting with angle

Q
Select the cutting angle using the cutting angle
scale
.
12
1.
Loosen the wing screw for cutting angle
preselector
, set the desired cutting angle
13
on the cutting angle scale
retighten the wing screw for cutting angle
preselector
.
13
2.
Switch the product on and operate as described.

Cutting with rip fence

Q
The rip fence
14
enables exact cuts along a
workpiece edge and cutting strips of the same width.
1.
Loosen the wing screw for rip fence
the rip fence
into the rip fence slot and
14
adjust to the desired width.
2.
Retighten the wing screw for rip fence
NOTe
The 0° cutting mark indicates the position of
u
the saw blade for right-angled cuts.
The 45° cutting mark indicates the position
of the saw blades for 45° cuts (Fig. E).
3.
Apply light lateral pressure to the workpiece
and guide the product along the edge when
cutting.

After use

Q
1.
Switch the product off, remove the battery
back
and let it cool down.
4
2.
Check, clean and store the product as
described below.

Cleaning and care

Q
WArNING!
Always switch the product off, remove
the battery pack and let the product
cool down before performing inspection,
maintenance and cleaning work!

Cleaning

Q
The product must always be kept clean, dry and
o
free from oil or grease. Remove debris from it
after each use and before storage.
Regular and proper cleaning will help ensure
o
safe use and prolong the life of the product.
Inspect the product before each use for worn
o
and damaged parts. Do not operate it if you
find broken and worn parts.
Never allow fluids to get into the product.
o
16 GB / IE / NI
and then
12
, insert
7
7
.
Clean the product with a dry cloth. Use a
o
brush for areas that are hard to reach.
In particular clean the air vents after every
o
use with a cloth and brush.
Remove stubborn dirt with high pressure air
o
(max. 3 bar).
NOTe
Do not use chemical, alkaline, abrasive or
u
other aggressive detergents or disinfectants
to clean this product as they might be harmful
to its surfaces.

Maintenance

Q
Before and after each use, check the product
and accessories (or attachments) for wear and
damage. If required, exchange them for new ones
as described in this instruction manual. Observe
the technical requirements (see "Technical data").

repair

Q
This product does not contain any parts that can
be repaired by the user. Contact an authorised
service centre or a similarly qualified person to
have it checked and repaired.

Storage

Q
Switch the product off and remove the battery
o
pack
.
4
Clean the product as described above.
o
Store the product and its accessories in a
o
dark, dry, frost-free, well-ventilated place.
Always store the product in a place that is
o
inaccessible to children. The ideal storage
temperature is between 10 °C and 30 °C.
We recommend using the original package for
o
storage or covering the product with a suitable
cloth or enclosure to protect it against dust.
Regularly check the charge level of the
o
battery pack, if it is to be stored for an
extended period. Optimum storage conditions
are cool and dry.

Transportation

Q
Switch the product off and remove the battery
o
pack
.
4
Attach transportation guards, if applicable.
o
Always carry the product by its handles.
o
Protect the product from any heavy impact
o
or strong vibrations which may occur during
transportation in vehicles.
Secure the product to prevent it from slipping
o
or falling over.

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis