Checking The Battery Level; Attaching / Removing The Saw Blade; Attaching / Removing A Dust Extraction Device; Checking The Blade Guard - Parkside PHKSAP 20-Li A1 Bedienungs- Und Sicherheitshinweise

Charging status LeDs
Green LED lights up
without battery pack
Green LED lights up
with battery pack
Red LED lights up
with battery pack
Red LED flashes with
battery pack
Green LED flashes
with battery pack

Checking the battery level

Q
Press the battery level button
o
charging level of the battery pack
status / remaining charge will be shown on
the battery level indication light
3 Red LEDs light up
2 Red LEDs light up
1 Red LEDs lights up low charging level
Charge the battery pack
o
when it is at medium or low charging level.
Attaching / removing the saw
Q
blade
WArNING!
Always remove the battery pack from the
u
product before changing the saw blade in
order to avoid switching it on accidentally.
Always use the correct accessories according
u
to the intended use! Observe the technical
requirements of this product (see section
Technical data) when purchasing and using
accessories!
Accessories can be sharp and become hot
u
during use! Handle them carefully! Wear
safety gloves when handling accessories in
order to avoid injuries like burns and cuts!
Never press the spindle lock whilst the
u
spindle is rotating!
The arrow on the accessory must correspond
u
to the arrow showing the direction of rotation
(running direction shown on the product).
Ensure that the accessory is suitable for the
u
rotational speed of the product.
1. Set the cutting depth to the minimum position,
0 mm (see "Setting the cutting depth").
14 GB / IE / NI
Charger ready
Battery pack fully charged
Battery pack charging
Battery pack defect
Battery pack too cold or
warm
23
to check the
. The
4
21
.
maximum charging level
medium charging level
4
before operation
2. Swing the blade guard
release lever and put the product down.
19
3. Press the spindle lock button
engages. Keep the button pressed and loosen
the clamping screw
4. Remove the clamping screw
and the clamping flange
5. Remove saw blade, if necessary.
6. Clean the flanges and spindle from dust.
7. Place a suitable saw blade, the clamping
flange 16 , the washer
screw onto the spindle. The arrow on
18
the saw blade must correspond to the arrow
showing the direction of rotation (running
direction shown on the product).
8. Press the spindle lock button
engages. Keep the button pressed and tighten
the clamping screw
9. Turn the saw blade by hand to test if it is
rotating smoothly. The blade should not flutter.
10. Switch the product on and let it run idle for
about one minute, to confirm that the saw blade
has been installed properly. Switch off the
product and re-fit the saw blade as described,
should there any abnormal vibration or
excessive noise occur.
Attaching / removing a dust
Q
extraction device
WArNING!
During operation fine dust will be generated!
u
Some dusts are highly inflammable and
explosive! Always attach a dust extraction
device when using this product in order to
keep the working area clean! Wear a dust
mask when operating this product! Dust can
be harmful to health! Especially dust and chips
of wood that has been treated, e.g. with wood
preservative or a stain!
Do not smoke during operation, keep heat
u
sources and open flames out of the working
area!
1. Connect an approved dust and chip extraction
device to the vacuum outlet for dust extraction

Checking the blade guard

Q
1. Pull the release lever for the blade guard
back as far as the stop. The blade guard
must move freely without jamming and
must spring back into its starting position
automatically when the release lever for the
blade guard is released.
19
back using the
15
until it
8
with the hex key 9
18
, washer
18
17
(Fig. D).
16
and the clamping
17
until it
8
18 with the hex key
9
19
15
.
.
.
20