Remaining Hazards; Technical Data; Before Starting The Equipment - Parkside PBS 350 A1 Bedienungsanleitung

• Blades that are misshapen or damaged in any way must
not be used.
• If the table insert is worn, replace it.
• Never operate the machine if either the door protecting
the blade or the detachable safety device are open.
• Ensure that the choice of blade and the selected speed are
suitable for the material to be cut.
• Do not begin cleaning the blade until it has come to a com-
plete standstill.
• For straight cuts of small workpieces against the longitudi-
nal limit stop the push stick has to be used.
• Wear gloves when handling the saw blade and rough
materials
• The bandsaw blade guard should be in its lowest position
close to the bench during transport.
• For miter cuts when the table is tilted, the parallel stop must
be positioned on the lower part of the table.
• Never use guards to lift or transport items.
• Ensure that the bandsaw blade guards are used and cor-
rectly adjusted.
• Keep your hands a safety distance away from the band-
saw blade. Use a push stick for narrow cuts.
• The push stick has to be stored on the intended device, so
that it can be reached from normal working position and is
always ready to be used.
• In the normal operating position the operator is in front of
the machine.
Warning! This electric tool generates an electromagnetic
field during operation. This field can impair active or pas-
sive medical implants under certain conditions. In order to
prevent the risk of serious or deadly injuries, we recommend
that persons with medical implants consult with their physi-
cian and the manufacturer of the medical implant prior to
operating the electric tool.

Remaining hazards

The machine has been built using modern technology in
accordance with recognized safety rules. Some remaining
hazards, however, may still exist.
• Risk of injury for fingers and hands by the rotating saw
band due to improper handling of the work piece. Risk of
injury through the hurling work piece due to improper han-
dling, such as working without the push stick.
• Risk of damaging your health due to wood dust and wood
chips. Wear personal protective cloth such as goggles.
Use a fitting dust extractor.
• Risk of injury due to defective saw band. Regularely check
saw band for such defects.
• Risk of injury for fingers and hands while changing saw
band. Wear proper gloves.
• Risk of injury due to starting saw band while switching on
the machine.
• The use of incorrect or damaged mains cables can lead to
injuries caused by electricity.
• Wear only closefitting clothes. Remove rings, bracelets
and other jewelry.
• For the safety of long hair, wear a cap or hair net. Even
when all safety measures are taken, some remaining haz-
ards which are not yet evident may still be present.
• Remaining hazards can be minimized by following the
instructions in „General safety instructions" „Proper Use"
and in the entire operating manual.

6. Technical data

Electro motor
Power
Revolutions n
0
Saw band length
Saw band width
Saw band width max.
Cutting speed
Passage height
Passage width
Table size
Slewing range of the table
Max. size of the workpiece
Overall weight
Subject to technical modifications!
* Operating mode S1, continous operation.
The work piece must have a minimum height of 3 mm and a
minimum width of 10 mm.
The total noise values determined in accordance with EN
61029.
Sound pressure level L
pA
Uncertainty K
pA
Sound power level L
WA
Uncertainty K
WA
Wear hearing protection!
The effects of noise can cause a loss of hearing. Keep the
noise level and vibration to a minimum!
• Only use faultless devices.
• Maintain and clean the device at regular intervals.
• Adapt your working methods to the device.
• Do not overload the device.
• Have the device checked if necessary.
• Switch the device off if it is not in use.

7. Before starting the equipment

Make sure the machine stands securely, i.e. bolt it to a work-
bench or solid base. There are two holes for this purpose in
the machine foot.
• The saw table must be mounted correctly.
• All covers and safety devices have to be properly fitted
before the machine is switched on.
• It must be possible for the blade to run freely.
• When working with wood that has been processed be-
fore, watch out for foreign bodies such as nails or screws
etc.
230 - 240 V∼ 50 Hz
S1 350W*
1400 min
-1
1400 mm
3,5-12 mm
12 mm
900 m/min
0 - 80 mm
200 mm
300 x 300 mm
0° bis 45°
400 x 400 x 80 mm
14,8 kg
77,4 dB(A)
3 dB
90,4 dB(A)
3 dB
GB 17