Herunterladen Inhalt Inhalt Diese Seite drucken

Battery Removal/Installation - Hitachi D 10DD Bedienungsanleitung

Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 11
English
APPLICATION
Driving and removing of wood screws, tapping
screws, etc.
Drilling of various metals.
Drilling of various woods.

BATTERY REMOVAL/INSTALLATION

1. Battery removal
Hold the handle tightly and push the battery latch
to remove the battery (see Figs. 1 and 2).
CAUTION
Never short-circuit the battery.
2. Battery installation
Insert the battery while observing its polarities (see
Fig. 2).
CHARGING
Before using the driver drill, charge the battery as
follows.
<UC12Y, UC12YA>
1. Connect the charger's power cord to an AC outlet.
When connecting the plug of the charger to a outlet,
the pilot lamp will blink in red. (At 1-second intervals).
2. Insert the battery into the charger.
Position the battery so that the nameplate faces
toward the ventilation slots of the charger and push
in the battery until it contacts the bottom plate. (See
Figs. 1 and 3.)
Table 1
Before charging
While charging
Charging complete
Charging impossible
Table 2 Charging time (at 20°C)
Charger
Battery
EB9
NOTE: The charging time may vary according to temperature and power source voltage.
<UC9SC>
1. Insert the battery in the charger.
Position the battery so that the nameplate faces
toward the nameplate of the charger and press in
the battery until it comes into contact with the
bottom plate. (See Figs. 1 and 3)
6
Indications of the pilot lamp
Blinks
Lights for 0.5 seconds. Does not lights for 0.5 seconds.
(off for 0.5 seconds)
Lights
Lights continuously
Blinks
Lights for 0.5 seconds. Does not lights for 0.5 seconds.
(off for 0.5 seconds)
Blinks
Lights for 0.1 seconds. Does not lights for 0.1 seconds.
(off for 0.1 seconds)
UC12Y
Approx. 60 min.
CAUTION:
If the batteries are inserted in the reverse direction,
not only recharging will become impossible, but it
may also cause problems in the charger such as
a deformed recharging terminal.
3. Charging
When inserting a battery in the charger, charging
will commence and the pilot lamp will light
continuously in red.
When the battery becomes fully recharged, the pilot
lamp will blink in red. (At 1-second intervals.) (See
Table 1)
(1) Pilot lamp indication
The indications of the pilot lamp will be as shown
in Table 1, according to the condition of the charger
or the rechargeable battery.
(2) Regarding recharging time
Depending on the combination of the charger and
batteries, the charging time will become as shown
in Table 2.
CAUTION
When the pilot lamp blinks rapidly in red (at 0.2-
second intervals), check for and take out any foreign
objects in the charger's battery installation hole. If
there are no foreign objects, it is probable that the
battery or charger is malfunctioning. Take it to your
authorized Service Agent.
4. Disconnect the charger's power cord from the AC
outlet.
5. Hold the charger firmly and pull out the battery.
UC12YA
Approx. 15 min.
2. Connect the charger power cord to the AC outlet.
Connecting the power cord will turn on the charger
(the pilot lamp lights up).
CAUTION
If the pilot lamp does not light up, pull out the
power cord from the AC outlet and check the battery
mounting condition.
UC9SC
Approx. 60 min.

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

D 10dg

Inhaltsverzeichnis