General Operation; Aux Operation; Cd/Usb Operation - Sharp XL-B710 Bedienungsanleitung

6

General Operation

Standby/ON
When you fi rst connect the unit to the mains socket, the unit will be in
STANDBY mode. Press the button on the remote control to switch the
main unit ON or OFF.
• When turning the system on, the system will start in the same mode as
during switch off .
• Disconnect the mains plug from the mains socket if you want to switch
the unit off completely.
• If there is no signal under the CD, USB, BT (Bluetooth) or AUX mode,
the unit will automatically switch off within 15 minutes.
Select Modes
Press the button repeatedly on the unit or press the CD/AUX, FM, USB
or BT PAIR buttons on the remote control to select the desired mode. The
selected mode will show on the display.
Adjust the Volume
• Press the VOL +/– buttons on the remote control or turn the VOLUME
+/- dial on the unit to adjust the volume.
• If you wish to turn the sound off , press the
control. Press the button again or press VOL+/- button on the remote
control or turn the VOLUME +/- dial on the unit to resume normal
volume.
Select the Equaliser
Press the EQ button on the remote control or on the unit repeatedly to
select: [Pop] - [Classic] - [Jazz] - [Rock] - [Flat]
Adjust the Brightness
Press the DIMMER button on the remote control to select brightness level.
Adjust the Bass
Press the BASS button on the remote control to enable and disable the
bass enhancement.
Set the Sleep Timer
This unit can switch to standby automatically after a set period of time.
1. Press the TIMER/SLEEP button on the remote control repeatedly to
select your desired time. The number of minutes will display in below
sequence: SLEEP 90 -> SLEEP 60 -> SLEEP 30 -> SLEEP 15 -> SLEEP 00
2. Stop pressing the SLEEP button when your desired time is displayed.
The sleep timer is now set.
– Press the SLEEP button to view the remaining time before switch off .
– To cancel the sleep timer, press the SLEEP button
repeatedly until "SLEEP 00" shows on the display.

AUX Operation

1. Ensure that the unit is connected to the TV or audio device.
2. Press the button on the main unit repeatedly or press the CD/AUX
button on the remote control to select AUX mode.
3. Operate your audio device directly for playback features.
4. Press the VOL +/– button to adjust the volume to your desired level.

CD/USB Operation

Tips:
• Supported MP3-CD formats is MP3 / CD.
• Unsupported fi le formats are skipped. For example, Word documents
(.doc) or MP3 fi les with extension .dlf are ignored and not played.
• USB supports maximum memory is 64GB.
button on the remote
CD Operation
1. Press the button repeatedly on the unit or press the CD/AUX
button on the remote control to select DISC mode.
2. Press the button on the unit or on the remote control and the disc
tray will open automatically.
3. Place the CD/MP3 disc with the label side up into the CD
compartment, and then press the
remote control to close the disc tray.
– The current playing time of the track will be shown on the display,
and unit will play the fi rst track on the CD/MP3 disc automatically.
– If there is no disc or the disc can't be read,
"NO DISC" will show on the display.
USB Operation
1. Insert the USB stick on the back of the unit.
2. Press the button on the main unit repeatedly or press the USB
button on the remote control to select USB mode.
Play Control
• To stop play, press the button on the remote control. The total tracks
of the CD will show on the display.
• To pause or resume play, press the
SCAN button on the remote control.
• To skip to the previous/next track, press the
or on the remote control.
• Press and hold the / buttons on the unit or on the remote control
to perform fast forward/reverse playback. Release the button to resume
normal playback.
• Press the ALBUM/PRESET
album (only for MP3/WMA discs).
• Press the INFO button on the remote control to display the current play
information.
Intro Playback
• Press the INTRO button on the remote control. The unit will play the fi rst
10 seconds of each track.
• Press the INTRO button on the remote control again to resume normal
playback.
Random Playback
• Press the SHUFFLE button on the remote control or the MODE button
on the unit to switch the randomly play the song ON/OFF.
– SHUFFLE: Randomly play the song. "
– SHUF OFF: Randomly turned off .
Select repeat play options
Press the REPEAT button repeatedly on the remote control or the MODE
button on the unit to select
button on the unit or on the
button on the unit or the
/ buttons on the unit
, buttons to skip to the previous/next
" lights up.
/