Inhaltsverzeichnis
Werbung
Quicklinks
Werbung
Inhaltsverzeichnis
Verwandte Anleitungen für Blaupunkt MC CD 40
Inhaltszusammenfassung für Blaupunkt MC CD 40
- Seite 1 CD Microsystem MC CD 40...
- Seite 2 MC CD 40...
- Seite 3 MC CD 40...
- Seite 4 MC CD 40...
- Seite 5 MC CD 40...
- Seite 6 MC CD 40...
- Seite 7 MC CD 40...
- Seite 8 MC CD 40...
- Seite 9 MC CD 40...
- Seite 10 MC CD 40...
- Seite 11 MC CD 40 CLASS 1 LASER PRODUCT...
- Seite 12 MC CD 40...
- Seite 13 MC CD 40...
- Seite 14 MC CD 40...
- Seite 15 MC CD 40...
- Seite 16 MC CD 40...
- Seite 17 MC CD 40...
- Seite 18 MC CD 40...
- Seite 19 MC CD 40...
- Seite 20 MC CD 40...
- Seite 21 MC CD 40...
- Seite 22 MC CD 40...
- Seite 23 MC CD 40...
- Seite 24 MC CD 40...
- Seite 25 MC CD 40...
- Seite 26 MC CD 40...
- Seite 27 MC CD 40...
- Seite 28 MC CD 40...
- Seite 29 MC CD 40...
- Seite 30 MC CD 40...
- Seite 31 MC CD 40...
- Seite 32 MC CD 40...
- Seite 33 MC CD 40...
- Seite 34 MC CD 40...
- Seite 35 MC CD 40...
- Seite 36 MC CD 40...
- Seite 37 MC CD 40...
- Seite 38 MC CD 40...
- Seite 39 MC CD 40...
- Seite 40 MC CD 40...
-
Seite 41: Safety Instructions
Brand name: Blaupunkt Responsible party: M3 Electronic GmbH Gutenbergstrasse 5, D-65830 Kriftel. Germany Hereby, Blaupunkt Competence Center Audio M3 Electronic GmbH, declares that this Class 1 equipment is in compliance with the essential requirement and other relevant provisions of Directive 1999/5/EC. - Seite 42 MC CD 40 12. ESD WARNING – the display does not function properly or not reaction to operation of any the control may due to the electrostatic discharge. Switch off and unplug the set. Reconnect after a few seconds. 13. DAMAGE REQUIRING SERVICE – the appliance should be serviced by qualified service personal when: a.
-
Seite 43: Electrical Information
MC CD 40 26. Ensure a minimum distance of 5cm around the apparatus for sufficient ventilation. 27. The ventilation should not be impeded by covering the ventilation opening with items such as newspapers, table-cloths, curtains, etc. 28. The batteries should be drawn to the environmental aspects of batter y disposal. - Seite 44 MC CD 40 Controls and connectors 1. IR receiver 8. EJECT /FUNCTION button 2. LED display 9. VOLUME control 3. STANDBY/PLAY/PAUSE button 10. AUDIO input 4. SKIP PREV button 11. SPEAKER outputs 5. CD loading drawer 12. PIGTAIL antenna 6. POWER button 13.
-
Seite 45: Controls And Connectors
MC CD 40 Controls and connectors 25. MUTE button 14. STANDBY button 15. CD button 26. REPEAT/MO/ST button 16. FM button / NEXT button /TUNER+ button 17. SEARCH/ button 29. ENTER button 18. SAVE/STOP button /TUNER- button 30. PROGRAM button /PRVE button 31. -
Seite 46: Connecting The Power
MC CD 40 Loudspeakers Placing & connecting the speakers • Unwrap the speaker wires. • Place a speaker on either side of the main unit, preferably at the same height, and with at least 150mm between each speaker and the main unit. -
Seite 47: Remote Control Batteries
MC CD 40 Remote control batteries Fitting or replacing the remote control batteries When replacing the batteries in the remote control, refer to the diagram above. 1. Push the catch on the battery door in the direction of the embossed arrow on the rear of the remote. -
Seite 48: Getting Started
MC CD 40 Getting started Switching on the MC CD 40 for the first time 1. Connect the mains plug to a wall outlet. 2. Extend the pig tail antenna as far as it can go. NOTE: The quality of the FM reception will be influenced by the positioning of the pigtail aerial. -
Seite 49: Scanning For Stations
MC CD 40 FM operation See Switching modes to switch to FM. Scanning for stations Before scanning for stations it is advised to position the antenna for best reception. Press the SEARCH button (17). The unit will perform a scan from 87.50 MHz to 108.00 MHz and store all found stations into the channel preset locations. - Seite 50 MC CD 40 Recalling station presets 1. Press the button to skip up through the preset channels 0-60 2. Press the button to skip down through the preset channels 0-60 3. You can also jump directly to a preset location by entering the location digits using the numeric buttons (21) eg:- Preset channel 27, you would type 2 &...
-
Seite 51: Numeric Buttons
MC CD 40 1. Press the PROGRAM button (30) to enter the program setup function. You will see the below appear on the display. Program indicator Track order Track to play 2. Use the numeric buttons to enter the tracks you want played in order. EG:- first track to be played is track 5 on the disc. -
Seite 52: External Input
MC CD 40 External input Connecting external audio sources External audio sources such as iPod's & MP3 players can be connected using a 3.5mm to RCA audio cable (not supplied). 1. Connect one end of the cable to the MP3 players headphone / Line output and the other end to the AUX IN input (10) on the back of the unit. -
Seite 53: Troubleshooting
MC CD 40 Trouble shooting PROBLEM CAUSE SOLUTION No sound Volume not turned up Adjust the main volume knob Adjust the antenna or move Static Sound Signal reception too low the unit to a stronger signal location Sound is distored... -
Seite 54: Specifications
Speaker Power:.........................2 x 5W FM:..........................87.5-108 MHz Net Weight:..........................3.0kg Contents The carton should contain: • The MC CD 40 Microsystem • 2 x Speakers • Remote control (with batteries) • Operating Manual LOCATION Place the unit on a dry stable surface away from heat and damp and where it is unlikely to... - Seite 55 There are separate collection systems for recycling in the EU. For more information, please contact the local authority or your retailer where you purchased the product. All rights reserved by Blaupunkt Competence Center Audio M3 Electronic GmbH. This material may be reproduced, copied or distributed for personal use only.