Herunterladen Diese Seite drucken

Switching Bt Drive Free 111 On/Off; Pairing (Connecting) With The Cell Phone; Re-Pairing; Exiting The Connection To The Cell Phone - Blaupunkt BT Drive Free 111 Bedienungsanleitung

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 1

Switching BT Drive Free 111 on/off

Switch-on: With switched-off device.
Hold the MFB button pressed for approx. 3 seconds until you hear a short
sound. The blue LED is on for 3 seconds.
Switch-off : The device is in standby mode (switched on).
Hold the MFB button pressed for approx. 3 seconds until you hear a long
sound. The red LED is on for 3 seconds. Afterwards, the device is switched
off .
IMPORTANT: After every switch-on, briefl y press the MFB button again to
establish the connection. The initial pairing is described below.

Pairing (connecting) with the cell phone

Before you can use the BT Drive Free 111, you must connect it with the
respective Bluetooth-ready cell phone (pairing). The following steps explain
the general procedure for pairing.
The distance between the two devices must be less than 1 metre.
The BT Drive Free 111 must be switched off .
Hold the MFB button pressed for approx. 6 seconds until you hear a long
sound. The LED starts to alternately fl ash red and blue.
Activate the Bluetooth function on your cell phone and look for "Audio
accessories". (For further details, please read the operating instructions
your cell phone.)
Select "BT DF 111" from the displayed list.
Upon request to enter the PIN code, enter "0000" and confi rm with "OK".
After successful pairing, you will hear a long sound and the LED is on for
approx. 3 seconds. The device is now in standby mode, which is indicated
every 3 seconds by the blue LED fl ashing briefl y. (Note: The PIN code is
preprogrammed and cannot be changed).
The range between cell phone and the device is limited to 10 m. The
shorter the distance, the better the connection.
IMPORTANT: If the pairing is not completed within 2 minutes, the LED goes
out and the device switches off again. In this case, start the pairing from the
beginning.
16

Re-pairing

After successful pairing, the BT Drive Free 111 is in standby mode. Before
making a phone call, ensure that the headphone icon on the display of your
cell phone is displayed, otherwise proceed as follows:
On the cell phone: In the Bluetooth menu, select "Paired devices", followed
by "BT Speaker" or "BT Drive Free 111".
On the BT Drive Free 111: Briefl y press the MFB button and confi rm (ac-
cept) it on your cell phone.
IMPORTANT: Always perform this brief activation if the headphone icon is
not shown (e.g. after extended switch-off of one of the devices or if you were
outside the range). (If your device supports automatic connection, briefl y
pressing the MFB button is suffi cient.)

Exiting the connection to the cell phone

If you want to connect the BT Drive Free 111 with other cell phones, you must
fi rst disconnect this connection.
Switch off the BT Drive Free 111.
Select "Disconnect" on your cell phone.
IMPORTANT: If the connection is lost, the BT Drive Free 111 sends three
sounds every minute. After 10 minutes, the BT Drive Free 111 completely
switches off .

Using the BT Drive Free 111

After the pairing has been successfully performed and the battery has been
charged, the following functions can be performed:
Call answering
To answer a call, briefl y press the MFB button or the answer button of
your cell phone.
Ending a call
Briefl y press the MFB button or the end button of your cell phone.
Rejecting a call
Hold the MFB button pressed for approx. 3 seconds until you hear a
short sound.
Redialing the last number
In standby mode, press the MFB button twice.
17

Werbung

Fehlerbehebung

loading