Herunterladen Inhalt Inhalt Diese Seite drucken

Fitting Procedure - Panasonic TY-WK42PV4W Anleitung Zur Anbringung

Wandhalterung zum anbringen des plasma-fernsehers (typ für vertikale anbringung)
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 6

Fitting procedure

1. Confirm the strength of the proposed fitting location.
(1) The weight of the wall-hanging bracket is approximately 7 kg (15.4 lbs). For the weight of the
plasma TV attached to the wall-hanging bracket, please see manual for the plasma TV.
(2) Check the wall strength at the 6 attachment locations by referring to the dimension drawing
of the wall-hanging bracket (given at right), and provide adequate reinforcement if strength
is not sufficient.
Notes
• There are 22 holes in the wall-hanging bracket.
If the wall material is wood, and adequate attachment strength
cannot be ensured by fastening at the 6 points at right, use
as many spare holes as necessary. However, exercise care
because some wall materials may crack if screws are located
too close together.
The following dimensions are important. Do not fit at any
location where these dimensions cannot be secured.
• For detailed dimensions for attaching the plasma TV, refer to
the separate External Dimension Drawing (page 46, 47).
• Do not attach or place anything other than the plasma TV on
the bracket.
2. Fit wall-hanging bracket to wall.
(1) Fit so that the arrow marks on the wall-hanging bracket point upward.
(2) Fasten the screw at the top center hole (A) first.
(3) Using a level, correct any bracket inclination, and then fasten screws at the remaining
5 locations.
Notes
• If the wall consists of a material such as concrete, and bolts or nuts must be embedded
beforehand, determine the hole positions using the actual wall-hanging bracket, or
calculate hole positions based on the dimension drawing and then embed bolts or
nuts with a nominal diameter of 6 mm. When embedding bolts, locate so that the bolts
protrude from the wall by 10 to 15 mm (25/64 to 19/32 inches).
• Use commercially available screws with a nominal diameter of 6 mm that are suited to
the wall material you are fitting the bracket to.
• Always fix firmly more than 6 places with a screw.
3. Fit the insulation spacers to the plasma TV.
(1) Place the plasma TV unit face down on a blanket or other soft cloth that is clean and free of debris, and follow the
procedure below.
(2) Remove terminal covers (if fitted) from the plasma TV.
(3) Using a flathead screwdriver, remove the four caps from the plasma TV.
Note
• Carefully retain the removed terminal cover and caps in a safe
place. (They will be needed again later should it be required
to use the special-purpose stand or standalone stand.)
(4) Using the included Allen wrench
head countersunk screws
and insulation spacers
where the caps were removed. (See the diagram at right.)
Refer to the page 46, 47 for details on selecting the
hexagon flat countersunk head screws
The bolt should be securely tightened to the torque given
below.
(11 - 13 N•m)
4
, fit the included Allen
or
dished toothed washers
(4 sets) into the holes from
or
.
[ Never use any other method
than specified to install.]
775 (38.5)
735 (28.9)
660 (26.0)
Plasma TV external profile
プラズマテレビ本体外形
プラズマテレビ本体外形
416 (16.4)
Wall-hanging bracket
Unit: mm (inches)
* Be sure to fit screws and tighten securely.
* Provide spacing around the plasma TV of at least 10 cm
(3.9") to the top and right side, at least 30 cm (11.8") to
the left side, at least 6 cm (2.4") to the bottom, leave a
clearance between the rear panel and the wall.
Flathead screwdriver
Cloth
Caps
Terminal cover
A
Wall attachment
holes (at 6 points)
(A)
or

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis