Werbung
Quicklinks
Werbung
Verwandte Anleitungen für HP LaserJet 4200L series
Inhaltszusammenfassung für HP LaserJet 4200L series
- Seite 1 LaserJet 4200L series avvio startgids...
- Seite 2 The information contained herein is subject to change without notice. The only warranties for HP products and services are set forth in the express warranty statements accompanying such products and services. Nothing herein should be construed as constituting an additional warranty.
- Seite 3 HP LaserJet 4200L series 412 mm (16.2 inches) 1045 mm (41.1 inches) HP LaserJet 4200L series 547 mm (21.5 inches) WARNING! The printer is heavy. To prevent physical injury, two people Prepare the location. Place the printer in a well-ventilated room on a should lift and move the printer.
- Seite 4 Make sure that the location has an adequate power supply. Check the Regulate the environment. Do not place the printer in direct sunlight or voltage rating on your printer (located under the top cover). The power near chemicals. Make sure that the environment does not experience supply will be either 110 to 127 Vac or 220 to 240 Vac, 50/60 Hz.
- Seite 5 Check the package contents. Make sure that all the parts are included. 3) Control panel overlay (this part might already be installed on the 1) Printer; 2) Right-angle power cord; printer.); 4) Print cartridge; 5) Software and documentation on CD-ROM. Vérification du contenu de l'emballage.
- Seite 6 Vista posteriore: 8) Sportello di accesso alla memoria; 9) Alloggiamento 1) Pannello di controllo; 2) Vassoio 1; 3) Indicatore del livello della carta; EIO (su alcuni modelli è installato un server di stampa HP Jetdirect 4) Vassoio 2; 5) Scomparto di uscita standard; 6) Coperchio superiore opzionale);...
- Seite 7 Remove the packing materials. 1) Remove the shipping bag and any 4) Open tray 1 and remove the orange sheet. 5) Open tray 2 and remove orange tape from the front and back of the printer. 2) Open the printer top all orange tape and packing materials.
- Seite 8 Install the print cartridge. 1) Remove the print cartridge from its 3) Lift the printer top cover. 4) Slide the print cartridge into the printer as packaging. 2) Bend and then pull the sealing tab from the end of the print far as it can go.
- Seite 9 Install any optional accessories. Use the separate installation 5) Duplexer for two-sided printing; 6) Storage cabinet instructions to install any accessories that you have purchased with the *The printer supports a maximum of one optional feeder. printer. 1) EIO accessories; 2) Hard disk; 3) 500-sheet feeder*; 4) Memory DIMM, flash DIMM, or font DIMM;...
- Seite 10 Load Tray 2. (For information about loading other trays, see the use guide 2) Pinch the release on the left guide and slide the guides to the correct on the CD-ROM.) 1) Pull tray 2 completely out of the printer. paper size.
- Seite 11 4) Rotate the blue knob on the right side of the tray to the correct paper 5) Load paper into the paper tray with the top edge of the paper facing the size. (Turn the knob to “STANDARD” for LTR, A4, LGL, EXEC, A5, and front edge of the tray.
- Seite 12 1) Collegare un cavo parallelo conforme allo un cavo di rete tra il server di stampa HP Jetdirect e una porta della rete. standard IEEE 1284 (tipo "B") tra la porta parallela del computer e la porta parallela della stampante.
- Seite 13 Connect the right-angle power cord. 1) Check the voltage rating on your 3) Connect the right-angle power cord between the printer and a grounded printer (located under the top cover). The power supply will be either 110 power strip or ac outlet. Note: If the optional duplexer has been installed, to 127 Vac or 220 to 240 Vac, 50/60 Hz.
- Seite 14 Install the control panel overlay (optional): 1) If necessary, remove the Turn the printer power on. Turn the power switch to the on position (“|”) overlay that is currently installed on the printer by inserting a thin, rigid and wait for the printer to warm up. If the printer automatically sets your object such as a credit card under the top edge of the overlay and then language, go to step 14.
- Seite 15 Set the control panel language. Use the (Up arrow) and (Down Test the printer. To verify that the printer is operating correctly, print a arrow) to scroll to a language you want and press (Select) to select it. configuration page. 1) Press (Select) to enter the menus.
- Seite 16 Note: If the configuration page does not print, make sure that there are no Install the printing software. Procedures for software installation vary messages (other than READY) on the control panel display, that the Ready according to the operating system and the network environment. Insert the light (top light) is on, and that no other lights are on or blinking.
- Seite 17 You can register at: http://www.register.hp.com. the software. If reinstallation fails, see the Readme on the CD-ROM, see the support flyer that came in the printer box, or visit http://www.hp.com. In the Select your country/region field at the top, select your country/region and click .
- Seite 18 1) The use guide on the CD-ROM; 2) This URL: http://www.hp.com/support/lj4200; 3) HP Customer Support (See the support flyer that came in the printer box.) Félicitations. Vous pouvez maintenant utiliser votre imprimante. Pour plus d'informations sur l'utilisation et le dépannage de l'imprimante,...
- Seite 20 © 2003 Hewlett-Packard Development Company, L.P. www.hp.com/support/lj4200 *Q3993-90902* *Q3993-90902* Q3993-90902...