Herunterladen Inhalt Inhalt Diese Seite drucken

Bosch PowerPack 300 Originalbetriebsanleitung Seite 28

Active line
Vorschau ausblenden Andere Handbücher für PowerPack 300:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 9
OBJ_BUCH-2074-001.book Page 5 Wednesday, August 14, 2013 12:19 PM
English–5
Error Code Indication
The components of the eBike system are continuously and au-
tomatically monitored. When an error is detected, the respec-
tive error code is indicated in text indication d.
To return to the standard indication, press any button on the
HMI 3 or on the operating unit 10.
Code
Cause
410
One or more buttons of the HMI are
blocked.
414
Connection problem of the operating
unit
418
One or more buttons of the operating
unit are blocked.
422
Connection problem of the drive unit Have connections and contacts checked
423
Connection problem of battery pack
424
Communication error among the
components
426
Internal time-out error
430
Internal battery pack of HMI empty
440
Internal error of the drive unit
450
Internal software error
490
Internal error of the HMI
500
Internal error of the drive unit
502
Illumination error
503
Error of the speed sensor
510
Internal sensor error
511
Internal error of the drive unit
530
Battery pack error
531
Configuration error
540
Temperature error
An improper load was detected.
550
602
Internal battery pack error while
charging
0 276 001 SAI | (14.8.13)
Depending on the type of error, the drive is automatically shut
off if required. Continued travel without assistance from the
drive is possible at any time. However, have the eBike
checked before attempting new trips.
 Have all checks and repairs performed only by an
authorised bike dealer.
Corrective Measure
Check if any buttons are blocked, e.g. from dirt or debris. Clean the
buttons, if required.
Have connections and contacts checked
Check if any buttons are blocked, e.g. from dirt or debris. Clean the
buttons, if required.
Have connections and contacts checked
Have connections and contacts checked
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Charge HMI (in holder or via USB port)
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Have the HMI checked
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Check the light and the associated wiring. Restart the system. If the
problem persists, contact your Bosch eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
Switch off the e-Bike, remove the battery pack and reinsert the battery
pack. Restart the system. If the problem persists, contact your Bosch
eBike dealer.
Restart the system. If the problem persists, contact your Bosch eBike
dealer.
The eBike is outside of the permissible temperature range. Switch off the
eBike system and allow the drive unit to either cool down or heat up to the
permissible temperature. Restart the system. If the problem persists,
contact your Bosch eBike dealer.
Remove load. Restart the system. If the problem persists, contact your
Bosch eBike dealer.
Unplug the charger from the battery pack. Restart the eBike system. Plug
the charger into the battery pack. If the problem persists, contact your
Bosch eBike dealer.
Bosch eBike Systems

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis