Accoppiamento Spinotto-Piede Di Biella; Gioco Radiale Testa Di Biella - Husqvarna TE 250 2007 Werkstatt-Handbuch

SEGMENTO
PISTON RING
KOLBENRING
SEGMENTO
Accoppiamento spinotto-piede di biella (A): 0,012÷0,027 mm.
Gioco radiale testa di biella (B): 0,026÷0,036 mm.
Gudgeon pin/conrod small end clearance (A): 0.00047÷0.00106 in.
Conrod big end radial clearance (B): 0.00102÷0.00141 in.
Accouplement tourillon-douille pied de bielle (A): 0,012÷0,027 mm. LIMITE DE SERVICE: 0,055 mm.
Jeu radial tête de bielle (B): 0,026÷0,036 mm.
Paarung Bolzen-Pleuelkopfbuchse (A): 0,012÷0,027 mm. ZULÄSSIGER GRENZWERT: 0,055 mm
Radialspiel des Pleuelkopfes (B): 0,026÷0,036 mm.
Acoplamiento eje del pistón-pie de biela (A): 0,012÷0,027 mm
Juego radial cabeza de biela (B): 0,026÷0,036 mm.
Part. N. 8000 A7735 (07-2006)
REVISIONE MOTORE
ENGINE OVERHAULING
REVISION MOTOR
MOTORUEBERHOLUNG
REVISIÓN DEL MOTOR
GIOCO AL MONTAGGIO (H)
**
NOMINAL CLEARANCE (H)
**
JEU AU MONTAGE (H)
**
SEGMENT
MONTAGESPIEL (H)
**
JUEGO EN EL MONTAJE (H)
**
"A" TE, TC 250: 0,011÷0,033 mm
(0.00043÷0.00130 in.)
"A" SMR 400: 0,050÷0,085 mm
(0.0020÷0.0033 in.)
"A" TC 450-510: 0,070÷0,110 mm
(0.0027÷0.0043 in.)
"A" TE-SMR 450: 0,065÷0,100 mm
(0.00256÷0.00394 in.)
"A" TE-SMR 510: 0,030÷0,065 mm
(0.0012÷0.0025 in.)
"B" TE-SMR 450: 0,035÷0,070 mm
(0.00138÷0.0027 in.)
"B" SMR 400; TE-SMR 510: 0,020÷0,055 mm
(0.0008÷0.0022 in.)
"C" TE, TC 250: 0,040÷0,110 mm
(0.0016÷0.0043 in.)
"C" SMR 400: 0,010÷0,180 mm
(0.0004÷0.0071 in.)
"C" TC 450-510: 0,040÷0,120 mm
(0.0016÷0.0047 in.)
"C" TE- SMR 450: 0,020÷0,110 mm
(0.0008÷0.0043 in.)
"C" TE- SMR 510: 0,010÷0,180 mm
(0.0004÷0.0071 in.)
LIMITE DI SERVIZIO: 0,080 mm
LIMITE DE SERVICE: 0,080 mm.
ZULÄSSIGER GRENZWERT: 0,080 mm.
LÍMITE DE SERVICIO: 0,055 mm
LÍMITE DE SERVICIO: 0,080 mm.
**
LIMITE DI SERVIZIO
** WEAR LIMIT
**
LIMITE DE SERVICE
**
ZULÄSSIGER GRENZWERT
** LÍMITE DE SERVICIO
0,07 mm
(0.0027 in.)
0,17 mm
(0.0067 in.)
0,22 mm
(0.0087 in.)
0,24 mm
(0.009 in.)
0,13 mm
(0.0051 in.)
0,15 mm
(0.0059 in.)
0,11 mm
(0.0043 in.)
0,22 mm
(0.0087 in.)
0,35 mm
(0.0138 in.)
0,24 mm
(0.0094 in.)
0,20 mm
(0.0079 in.)
0,35 mm
(0.0138 in.)
LIMITE DI SERVIZIO: 0,055 mm
WEAR LIMIT: 0.0022 in.
WEAR LIMIT: 0.00315 in.
G.29