Herunterladen Diese Seite drucken

Siemens SIMATIC IFP1500 ETH Betriebsanleitung

Industrial flat panels
Vorschau ausblenden Andere Handbücher für SIMATIC IFP1500 ETH:

Werbung

Gerät einbauen
1
Mounting the device
Vor Einbau und Inbetriebnahme – Before mounting and commissioning
1.1
WICHTIG: Beachten Sie alle dem Gerät beiliegenden
Dokumente und die Betriebsanleitung, bevor Sie das
Gerät einbauen und anschließen. Die vollständige
Dokumentation des Geräts finden Sie auf der beiliegen-
den DVD "Documentation and Drivers" und im Internet
(https://support.industry.siemens.com/cs/ww/de/ps/
16788/man).
IMPORTANT: observe all documents enclosed with the
device and the operating instructions manual before
mounting and connecting the device. You find the
complete documentation of the device on the enclosed
„Documentation and Drivers" DVD and on the internet
(https://support.industry.siemens.com/cs/ww/en/ps/16788/man).
Das Handbuchsymbol weist auf detaillierte Informationen in der Betriebsanleitung hin.
The manual symbol refers to detailed information in the operating instructions.
Zulässige Einbaulagen – Valid Mounting positions
1.2
50 °C
0 °C
40 °C
40 °C
0°–35°
0°–35°
0 °C
0 °C
1.3 Gerät einsetzen – Installing the HMI device
0.5
2-6
Enclosure
Type 4X/12
1
w
h
x
y
y
z
x
y
y
x
y
z
50
50
10
1.4 Gerät befestigen – Mounting the device
Mounting
12 x
clips
1
2
0.5 x 3
= 0.5 Nm
40 °C
0 °C
35 °C
0°–35°
0°–35°
0 °C
2
I F P
1 5
0 0
E T
H
IFP1500 ETH
y
y
x
x
z
y
y
IFP1500 ETH
Gerät anschließen
2
Connecting the device
2.1 Schutzleiter anschließen – Connecting the protective earth
1
35 °C
0 °C
2.2 Stromversorgung anschließen – Connecting the power supply
1
+1
+1
I F P
w
h
0
0
1 5
0 0
382
241
3
2
mm
2.3 Leitungen sichern – Securing the cables
Sichern Sie die angeschlossenen Leitungen zur Zugentlastung mit Kabelbindern an den markierten
Befestigungselementen.
Achten Sie darauf, dass die Leitungen durch die Kabelbinder nicht gequetscht werden.
Use cable ties to secure the connected cables to the selected fixing elements for strain relief.
Make sure that the cables are not crushed by the cable tie.
For use in Canada:
Arrêtez les câbles raccordés pour une décharge de traction avec les attache-câbles sur les
éléments de fixation marqués.
Veillez à ce que les câbles ne soient pas écrasés par les serre-câbles.
M4
2
T20
3
²
16 mm
24 VDC
Das Gerät darf nur an eine DC 24 V-Stromversorgung
angeschlossen werden, die den Anforderungen einer
sicheren Kleinspannung (SELV/PELV) z. B. gemäß der
IEC/EN/DIN EN/UL 60950-1 entspricht.
The device must only be connected to a 24 VDC
power supply which satisfies the requirements of safe
extra low voltage (SELV/PELV) e. g. according to
IEC/EN/DIN EN/UL 60950-1.
E T
H
4
0/OFF
5
M
L +
I F P
1 5
0 0
E T
H
²
2.5 mm

Werbung

loading

Inhaltszusammenfassung für Siemens SIMATIC IFP1500 ETH

  • Seite 1 Dokumente und die Betriebsanleitung, bevor Sie das Gerät einbauen und anschließen. Die vollständige Dokumentation des Geräts finden Sie auf der beiliegen- den DVD "Documentation and Drivers" und im Internet (https://support.industry.siemens.com/cs/ww/de/ps/ 16788/man). IMPORTANT: observe all documents enclosed with the device and the operating instructions manual before I F P mounting and connecting the device.
  • Seite 2 Since variance cannot be precluded entirely, we cannot guarantee full consistency. However, the information in this publication is reviewed regularly and any necessary corrections are included in subsequent editions. 3.3 Inbetriebnahme im PCC – Commissioning in the PCC Siemens AG Division Digital Factory Postfach 48 48 90026 NÜRNBERG...