Grundig CDP75 Bedienungsanleitung Seite 10

Allgemeiner Teil / General Section
OPERATION
Playing a CD
1 Open the lid by pressing the OPEN button.
2 Insert an audio CD, printed side up.
3 Push gently on the CD center so that it fits onto the hub.
4 Close the lid by pushing it on its left-hand side.
Display indication of:total number of tracks / total playing
time, i.e.
5 Press the PLAY/PAUSE 2; button to start CD play.
Display indication of:
current track / elapsed time of current track, i.e.
Adjusting volume and sound
• Adjust the volume for the headphones with the VOLUME control.
• Set the UBS switch (bass level) to the desired position.
The display indicates 2 pointing at the UBS logo
Interrupting CD play
1 You can interrupt CD play by pressing the PLAY/PAUSE 2; button.
Display indication: time of the current position (flashing).
2 Continue CD play by pressing the PLAY/PAUSE
Stopping CD play
• Press the STOP 9 button to stop CD play.
Display indication of: total number of tracks / the total playing time.
• If you press the STOP 9 button again, you will switch off the set.
Note: If no button is pressed for 10 seconds, the set will switch off automatically.
Removing the CD
• Hold the CD by its edge and press the hub gently.
Operation
PROGRAM – programming of tracks (max. 20 tracks)
1 Select with PREV ∞ or NEXT § the desired track.
2 As soon as the desired track is displayed, press the PROGRAM button to store the
track in the memory.
Display indication of: track number /
P / total number of stored tracks, i.e.
Notes:
- When you try to store more than 20 tracks,
the display indicates FULL.
- When you press PROGRAM and there is no track selected,
the display indicates SELECT.
Playing the program
• If you have selected the tracks in STOP mode, press the PLAY/PAUSE 2; button .
• If you have selected the tracks during CD play, first press the STOP 9 and then the
PLAY/PAUSE 2; button.
Display indication: PROGRAM.
Your program will be played in the selected playing mode (i.e. shuffle).
Checking the settings
• Press the PROGRAM button for more than 2 seconds.
Display indication: each stored track successively flashes for a short moment.
If no program is stored, the display shows NO PROG.
Erasing the program in STOP mode
• Press the STOP 9 button to erase the program.
The display shows CLEAR for a short moment, PROGRAM
disappears from the display and your program is erased.
Note: Interrupting the power supply or opening the lid will also erase the program.
1 - 10
2
UBS
RESUME
REPEAT
2;
button again.
PROGRAM
PROGRAM
PROGRAM
Operation
PREV ∞ / NEXT §
Selecting another track
• Briefly press the PREV ∞ or NEXT § button once/several times to skip to the
beginning of the current/previous or next track(s).
Display indication of: selected track number.
During play: CD play continues automatically with the selected track.
In stop position: press the PLAY/PAUSE 2; button to start CD play.
Searching for a passage during CD play
1 Hold down the PREV ∞ or NEXT § button to find a particular passage in forwards
or backwards direction.
CD play continues at a low volume. After 2 seconds, searching will start at high
speed.
2 Release the button when you have reached the desired passage.
Note: In the SHUFFLE mode or when playing a CD-program, searching is only possible
within the particular track.
SHUFFLE - play in random order
1 Press SHUFFLE to play all tracks of the CD or CD-program in random order until all of
them have been played once. The display shows SHUFFLE.
2 To switch off this function, press SHUFFLE again.
REPEAT
1 Press REPEAT to play repeatedly all tracks of the CD or CD-program.
The display indicates 2 pointing at the REPEAT logo.
2 To switch off this function, press REPEAT again.
Note: SHUFFLE and REPEAT can be used simultaneously: all tracks are played
repeatedly in random order.
Operation
RESUME / HOLD
RESUME – playing from where you have stopped:
• Activate the RESUME feature by sliding the
RESUME/HOLD switch to the middle.
The display indicates: 2 pointing at the RESUME logo:
UBS
2
RESUME
REPEAT
• If you stop CD play by pressing the STOP 9 button, the last played position will be
stored.
• Press the PLAY/PAUSE 2; button to resume CD play.
CD play starts from the position where it was stopped.
Note: Do not open the lid. Otherwise, the information about
the position last played, gets lost.
HOLD – deactivating all buttons
• Activate the HOLD feature by sliding the RESUME/HOLD switch to the very right.
Now, all buttons are deactivated and will not function until you switch the feature off
again. The lid cannot be opened.
If you press a button (except OPEN), the display will indicate HOLD.
Note: In the hold position, the resume function is automatically activated.
CDP 75 / CDP 110
UBS
RESUME
2
REPEAT
O
N
H O
R E
S U L D
M
E
GRUNDIG Service