Inhaltsverzeichnis
Werbung
Verfügbare Sprachen
Verfügbare Sprachen
•
The electric cable with which the snow thrower is con-
nected must always be intact. It must never be used if it
displays signs of damage.
•
The snow thrower must never be used if its plug, electric
cable or other electrical equipment is damaged.
•
Repairs to the electrical equipment may only be carried
out by an authorised electrician.
•
Never drive over the electric cable for the snow thrower
while working.
•
If the electric cable for the snow thrower has been dam-
aged while working, the following instructions must be
followed:
A. Stop the motor.
B. Leave the site in the opposite direction from the dam-
aged
point on the cable.
C. Disconnect the cable from the power socket.
•
Stop the motor and disconnect the power supply:
A. If the driver leaves the machine.
B. If the auger housing or discharge chute is blocked and
must be cleaned.
C. Before beginning repairs or adjustments.
•
Stop the engine and disconnect the spark plug cable:
A. If the machine steers away from the driving position.
B. If the auger housing or discharge chute is blocked and
must be cleaned.
C. Before beginning repairs or adjustments.
•
Always make sure the rotating parts have stopped and all
the controls are disengaged before cleaning, repairing or
inspection.
•
Never drive across a slope. Move from the top down, and
from the bottom to the top. Be careful when changing
direction on a slope. Avoid steep slopes.
•
Never operate the machine with insufficient protection or
without the safety devices in place.
•
Existing safety devices must not be disconnected or
disengaged.
•
Never use the snow thrower near enclosures, cars,
windowpanes, slopes etc. without properly setting the
discharge chute deflector.
•
Always keep children away from areas to be cleared. Get
another adult to keep the children under supervision.
•
Do not overload the machine by driving it too fast.
•
Take care when reversing. Look behind you before and
during reversing to check for any obstacles.
•
Never point the discharge chute towards bystanders. Do
not allow anyone to stand in front of the machine.
•
Disengage the auger when the snow thrower is to be
transported or is not in use Do not drive too fast on
slippery surfaces when transporting.
•
Only use accessories that are approved by the machine's
manufacturer.
•
Never drive the snow thrower in bad visibility or without
satisfactory lighting.
•
Always ensure you have a good balance and a tight grip
on the handle.
•
Never use the snow thrower on a roof.
ENGLISH
2.4
MAINTENANCE AND STORAGE
•
Tighten all nuts and screws so that the machine is in safe
working condition.
•
Never flush the machine with water. It will make damage
to the electrical equipment and risk of electrical shocks.
•
Check all electrical equipment before use. The snow
thrower must never be used if its insulatings, fittings or
other electrical equipment is damaged.
•
Always use genuine spare parts. Non-genuine spare parts
can entail a risk of injury, even if they fit the machine.
•
Before a long storage, check the instructions for
recommendations.
•
Replace damaged warning and instruction stickers.
•
Let the engine run a couple of minutes with the auger
connected after use. This prevents the auger from
freezing solid.
3.1
UNPACKING
1. Open the packing and take out all parts.
2. Check that all parts are supplied. The parts are as follows:
•
Lower part of the handle (1:D)
•
Upper part of the handle (1:C)
•
Start control (1:A)
•
Cable holder (1:B)
•
Six black knobs (2, 3, 8:M)
•
Four long screws with square fittings (2, 3:L)
•
Two short screws with square fittings (8:O)
•
Four screws with washers for the chute attachment (7:Q)
•
Chute attachment (7:R)
•
Ratchet with springs for the chute (5:S)
•
Chute (1:H)
•
Two plane washers for the deflector (8:P)
•
Deflector (1:I)
•
Cable holders (1:B)
•
Two clamps for fixing of the cable (4:O)
•
Two screws for the start control (4:N)
•
Chute clearing tool (1:G)
3. If anything is missing or damaged, take immediately
contact with the supplier.
3.2
HANDLE
3.2.1 Lower part of the handle
See fig. 2.
Assemble the lower part of the handle with two knobs and
two long screws with square fittings.
3.2.2 Upper part of the handle
See fig. 3.
Assemble the cable holder (3:B) to the upper part of the
handle.
Assemble the upper part of the handle on the lower part of the
handle. Fix with two long screws with square fittings and two
knobs.
3 ASSEMBLY
EN
25
Werbung
Inhaltsverzeichnis
