Herunterladen Inhalt Inhalt Diese Seite drucken

Viessmann 2622 Bedienungsanleitung Seite 10

Gleiskraftwagen mit motorisch bewegtem kran, funktionsmodell für zweileitersysteme
Inhaltsverzeichnis

Werbung

Führen Sie für die Programmierung mittels Märk-
lin-Motorola-Zentralen zunächst einen Reset an der
Zentrale durch (durch gleichzeitiges längeres Drü-
cken der Tasten „Stop" und „Go") oder schalten Sie
die Zentrale kurz aus und wieder ein. Wählen Sie
zunächst die aktuelle Adresse des Decoders oder
die Adresse 80 (wenn Sie z. B. die aktuelle Adres-
se des Decoders nicht kennen). Bei der Ausliefe-
rung hat der Decoder die Adresse 3. Stellen Sie alle
Funktionen (Funktion, F1 – F4) auf „Off".
Drücken Sie als nächstes die „Stop"-Taste der Zen-
trale. Betätigen Sie dann den Richtungsumschalter
und halten Sie ihn gedrückt. Drücken Sie kurz die
„Go"-Taste. Sobald die Beleuchtung des Fahrzeugs
blinkt (nach ca. 2 Sekunden), befindet sich der De-
coder im Programmiermodus und Sie können den
Umschalter loslassen.
Im Programmiermodus können Sie die Register des
Decoders wie folgt programmieren:
1. Wählen Sie ein Register zum Programmieren aus,
indem Sie die Nummer des Registers als Motoro-
la-Lokadresse an Ihrer Zentrale eingeben. Beach-
ten Sie, dass bei manchen Zentralen eine führen-
de 0 eingegeben werden muss.
2. Betätigen Sie den Richtungsumschalter. Die
Beleuchtung blinkt schneller.
3. Geben Sie den gewünschten Wert des Regis-
ters ein, indem Sie den Wert als Motorola-Lok-
adresse an Ihrer Zentrale eingeben. Der Wert Null
ist über die Motorola-Adresse 80 erreichbar.
4. Betätigen Sie den Richtungsumschalter erneut.
Die Beleuchtung fängt wieder an langsam zu blin-
ken.
Wiederholen Sie die Punkte 1 – 4 für alle Regis-
ter, die Sie programmieren wollen. Um ein Regis-
ter zum Programmieren auszuwählen oder einen
Wert für ein Register einzugeben, müssen Sie die
eingegebene Zahl immer wie beim Auswählen ei-
ner Lokadresse an Ihrer Zentrale bestätigen. Die
Beleuchtung zeigt an, welche Eingabe der Decoder
erwartet:
- Beleuchtung blinkt: Eingabe einer Registernum-
mer.
- Beleuchtung blinkt schneller: Eingabe des Wer-
tes eines Registers. Zum Beenden des Program-
miermodus drücken Sie „Stop".
5.4 Programmierung von Werten größer 80 im
Motorola Langmodus.
Um vom klassischen Motorola-Programmiermodus
in den erweiterten oder Motorola-Langmodus zu ge-
langen, programmieren Sie zunächst wie oben be-
schrieben Register 7 mit Wert 7.
Daraufhin blinken die Stirnleuchten (rot/weiß) zwei-
mal lang, gefolgt von einer langen Pause, dann wie-
10
For programming the decoder with any of the Märk-
lin Motorola central units first activate a reset of the
command station (by simultaneous pressing of the
"Stop" and "Go" buttons for a few moments) or turn
off the command station and then back on again.
Then select the current address of the decoder or
the address 80 (if, for instance, you do not know
the current address of the decoder). The factory
default value is 3. Turn all functions off (F1 – F4).
Then press the „Stop" button of the command
station. After that activate the change-of-direction
switch and keep the throttle knob pressed down.
Press the "Go" button. As soon as the lighting of
the vehicle starts blinking (after about 2 seconds)
the decoder has switched to programming mode.
Now you may release the throttle knob.
You may program the register of the decoder as
follows while in programming mode:
1. Select a register that you want to program by en-
tering the number of the register as a Motorola
locomotive address on your command station.
Please note that with some command stations
you have to enter "0" first.
2. Activate the change-of-direction switch. The light-
ing blinks faster.
3. Enter the desired value for the register by enter-
ing the value as a Motorola locomotive address
on your command station. The value zero can be
reached by the Motorola address 80.
4. Activate the change-of-direction switch again. The
lighting blinks slower again.
Repeat points 1 – 4 for all registers you want to
program. In order to select a register for programming
or for entering a value into a register you have to
confirm the entered value (number) in the same
manner as if selecting a locomotive number on
your command station. The lighting indicates which
command is expected by the decoder:
- Lighting blinks: Entry of a register number.
- Lighting blinks faster: Entry of a value for a regis-
ter. For terminating the programming mode press
the "Stop" button.
5.4 Programming of values greater than 80 in
the Motorola long mode.
In order to move from the classic Motorola pro-
gramming mode into the extended or Motorola long
mode first program register 7 with the value 7 as
described above.
The front and rear lights start to blink (red/white)
twice long, followed by a long pause after which

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Diese Anleitung auch für:

26202621H0 robel

Inhaltsverzeichnis