Before Use Connections; Connection Panel - Pioneer EFX-1000 Bedienungsanleitung

CONNECTIONS

Connection Panel

1 Power input socket (AC IN)
Use the provided power cord to connect this socket to an
AC outlet.
2 POWER switch
3 Digital OUTPUT fs SELSECT switch
Use to change the digital output frequency sampling rate
(fs) (44.1kHz/48kHz/96kHz).
4 Link input/output connector (EFX LINK)
When the accessory digital link cable is used to connect
this connector to the DJ-mixer DJM-1000 (with digital link
support), digital link functions can be used, permitting a
variety of new functions.
CAUTION:
The EFX LINK connector is designed to be connected
via the provided digital link cable ONLY to a component
equipped with the designated digital link function.
The unit may be damaged if this connector is
mistakenly connected to any other component.
5. MIDI input/output connectors (MIDI OUT/THRU,
MIDI IN)
Use to connect the effector to a MIDI component (see page 23).
6 Digital input/output connectors (DIGITAL IN,
DIGITAL OUT)
Use to connect the effector to a component provided with
coaxial digital input/output connectors.
7 Foot switch jack (FOOT SW)
Can be connected to a ON/OFF type foot switch with 6.3mm
phone plug to allow ON/OFF control of effects.
Foot switches are available in several types, including
press-ON, press-OFF, and latching-type ON/OFF.
8 Input/output gain select switch (IN&OUT LEVEL)
Use to select the input/output gain (–10dB / +4dB).
Installation Location
÷ Avoid mounting on top of amplifiers, near spotlights, or
other heat-emitting components and appliances;
extended exposure to heat can cause damage to the
effector itself.
÷ Install this unit as far as possible away from tuners and TV
sets. A unit installed in close proximity to such equipment
may cause noise or degradation of the picture.
1 2 3
6 7
4 5
8 9
9 Audio INPUT/OUTPUT jacks
Uses 6.3mm phones plug. For monaural inputs, connect L
input channel only for output on both L and R channels.
Audio inputs are throughput (output) even when the unit's
power is turned OFF.
10 Audio INPUT/OUTPUT jacks
INPUT/OUTPUT connectors using RCA pin jacks.
Audio inputs are throughput (output) even when the unit's
power is turned OFF.
7 Before making or changing the connections,
switch off the power switch and disconnect the
power cord from the AC outlet. This precaution
should also be taken when changing the IN & OUT
LEVEL switch and DIGITAL fs SELECT switch.
÷ When connections are made to the phone jack inputs
and a monaural signal cable is connected to the L
(MONO) terminal, inputs can be made to both the L and
R channels.
÷ After all other connections are made, connect the power
cord to a household wall outlet or to the auxiliary AC
power takeoff on your amplifier.
See page 23 for instructions on how to
use the MIDI terminals.
CAUTION:
Do not make any connections that may create signal
loops as this will cause circuit oscillations which
could damage the speakers.
[Example of connections that must not be
performed]
¶ Do not connect the output of the DJ Mixer to the
input terminal of the Effector and the output of the
Effector to the input terminal of the same mixer.
¶ Do not connect the SEND output of the DJ Mixer to
the input terminal of the Effector and the output of
the Effector to the input terminal of the DJ Mixer
(except for the RETURN terminal).
Cleaning the unit
To clean the unit wipe with a polishing or a soft, dry cloth.
For stubborn dirt, moisten a soft cloth with a weak solution
of neutral detergent (diluted in five to six parts water),
wring the cloth well, and wipe away the dirt. Use a dry cloth
to wipe the surface dry. Do not use volatile liquids such as
benzene or thinner which will damage to the unit.
BEFORE USE (CONNECTIONS)
10
<DRB1368>
9