Other Troubleshooting - Pioneer EFX-1000 Bedienungsanleitung

TROUBLESHOOTING
Incorrect operations are often mistaken for trouble and malfunctions. If you think there is something wrong with this
component, check the points below. Sometimes the trouble may originate from another component. Thus, also check the
other electrical appliances also in use.
If the trouble cannot be rectified even after checking the following items, contact your dealer or nearest PIONEER service
center.
Symptom
No power
No sound, or too low
Analog inputs aren't output
Digital signals aren't output.
When set to BYPASS, analog
signals aren't output.
Effect sounds aren't applied.
No effect sound is heard when
beat effects are applied.
Probably cause
÷ Power cord isn't connected.
÷ Connection cords are loose or aren't con-
nected properly.
÷ Connector terminals and plugs are dirty.
÷ Input level is set too low.
÷ Effect output level is set too low.
÷ A digital or EFX LINK input is connected.
When analog and digital inputs are connected
simultaneously, the digital input is given
priority.
÷ The DJ mixer (DJM-1000) connected by EFX
LINK has its effecter link set to ON (EFX LINK).
÷ EFX LINK is connected to DJ mixer (DJM-
1000) via digital link cable.
÷ The digital output fs setting does not match
the connected component.
÷ No analog inputs are connected.
Even if a digital input or EFX LINK is
connected, analog inputs are output as analog
during BYPASS mode.
÷ The lever switch is set to [OFF].
÷ MIX dial is set to [MIN].
÷ DEPTH dial is set to [MIN].
÷ EFFECT OUT LEV. dial is set to [MIN].
÷ BYPASS button is ON.
÷ EFFECT FREQUENCY indicators (HI, MID,
LOW) are all off (during use of TRANS,
FLANGER, FILTER, or PHASER effects).
÷ Some combinations of effects may have weak
results. Particularly, some combinations of
beat effects and digital jog break may sound
weak.
÷ EFFECT FREQUENCY indicators (HI, MID, LOW)
are all off (during use of DELAY, ECHO, PITCH
ECHO effects).
OTHER (TROUBLESHOOTING)
Remedy
÷ Connect power cord to outlet.
÷ Connect properly.
÷ Wipe away dirt and soil.
÷ Rotate INPUT LEVEL dial toward right
([MAX] direction).
÷ Try setting IN&OUT LEVEL switch to the
opposite position.
÷ Rotate EFFECT OUT LEV. dial toward right
([MAX] direction).
÷ Cancel the EFX LINK, and disconnect any
digital input with priority over analog
inputs.
The order of priority of inputs is:
EFX LINK > Digital input > Analog input.
÷ If EFX LINK is connected to DJ mixer (DJM-
1000) via digital link cable, ordinary digital
signals are not output.
Disconnect the digital link cable.
÷ Set the digital output fs to match the
connected component.
÷ Use analog signals for input. Or use digital
output. Outputs when BYPASS is selected
are as follows:
Input
connection Analog output
conditions
Analog only Analog source
Digital only (no output)
Analog &
Analog source
digital
÷ Either hold lever switch in [ON] position, or
set to [ON/LOCK].
÷ Rotate MIX dial toward the right ([MAX]
direction).
÷ Rotate DEPTH dial toward the right ([MAX]
direction).
÷ Rotate EFFECT OUT LEV. dial toward the
right ([MAX] direction).
÷ If BYPASS indicator is flashed, no effects
will be output. Press BYPASS so that the
indicator goes out.
÷ If EFFECT FREQUENCY indicators are all off,
only the original sound will be output. Press
the button corresponding to the frequency
band to which you wish to apply effects (the
button's indicator will light).
÷ Try setting SIGNAL FLOW switch to the
opposite position (reverse order of signal
processing for beat effects and digital jog
break).
÷ If EFFECT FREQUENCY indicators are all off,
no effect sound will be output. Press the
button corresponding to the frequency band
to which you wish to apply effects (the
button's indicator will light).
Digital output
Analog source
Digital source
Digital source
27
<DRB1368>