Herunterladen Inhalt Inhalt Diese Seite drucken

General Information - Märklin Central Station Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für Central Station:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Using the following submenu, you can assign locomotives from the
Central Station's locomotive list to this Mobile Station, locomotives
which are to be controlled with the Mobile Station. You therefore
have the possibility of
allowing another operator
to have access to a
limited number of loco-
motives. The locomotive
list in the Mobile Station
has a capacity for up to
10 entries.
After you have selected
the desired component,
a settings field will appear
in which locomotives
for the Mobile Station's
locomotive list are can
be selected or removed
from this list. This is done
in the same manner as
with the generation of
a multiple unit motive
power combination from
the Central Station's loco-
motive list. The changes
are not active until the
new settings have been
confirmed (control area
with the check mark in
the lower right).
In the "Expanded" control area you have the possibility of changing
or adding to the designation for the Mobile Station you have just se-
lected. The keyboard blended into the screen will help you here. This
function only makes sense, when more than one auxiliary
Mobile Station is being used.
Important! When a Mobile Station with an older version of the
internal database than the version present in the
Central Station is connected to that Central Station,
the database in the Mobile Station is automatically
updated. This process can take as long as 2 minutes!
Booster Configuration
Select the line „External Booster Control" as shown in the illustration
on page 39. The window „Delay short-circuit detection" will open up.
As a matter of principle, the highest possible value of 2,000 millise-
conds is set; this is permissible for Märklin Boosters. You can also
set a smaller value; the Central Station will then shut off faster in the
event of a short circuit.
Access Authorization
Here, you can block access to different options on the Central Stati-
on in order to prevent unauthorized persons from changing or even
deleting locomotives or from activating a Reset.
• „Block Stop" prevents the emergency halt when the Stop button is
pressed. This affects the internal stop button and all stop buttons
in the Sniffer.
• „Block creating operations" prevents the addition of locomotives,
turnouts, routes, etc. This is useful for display layouts on which
people can run or operate things but on which no changes are
supposed to be made.
• „Block reset operation" deactivates the reset to factory default
settings. The Central Station comes from the factory set this way.
Central Station mit Update 60212
• „Block deleting operations" prevents changing locomotives,
turnouts, etc.
Code Query
You can protect access to the submenu „Access Authorization" with
an access code. With this you can prevent the settings from being
changed without authorization.
You must first decide on a number code. This code is then queried
before access to this menu is possible.
• Changing the Access Code
Pressing on the control surface „Change Access Code" opens the
entry dialog for the new code.
• Delete the old code – if present – and enter the new code.
• Confirm your entry.
Make a mental note of your access code.
If you should forget it, you can only reset it th-
rough the computer interface.
The consumer must bear the cost of having
the code rest at the factory!
• Activating the code – check the box next to „Protect Access
Authorization".
• The next time the menu „Access Authorization" is called up,
you must enter your assigned code.

General Information

Here you will find important information about the Central Station.
Note: Please have the hardware and software version numbers given
in this settings field handy before you call the Märklin telephone ser-
vice for help. This will result in a more efficient malfunction analysis.
The software version is the version of the internal opera-
ting software. Important: When you contact Märklin with
questions about your Central Station, you must have this
number ready.
The internal serial number is uniquely assigned to your
unit. You need this number to register your Central
Station with us. You must have this number ready for
inquiries, because we need this number in order to be
able to help you further.
7. Computer Interface
The computer interface makes it possible to connect the
Central Station to your personal computer. It doesn't matter here if
you are using a MS Windows ® , Apple ® , or Linux ® computer. The
Central Station makes use of open standards for data transmission
and does not require installation of software on your computer. An
Internet browser must be installed and configured. You can down-
load updates through the computer interface, safeguard all configu-
ration data for the Central Station and produce them again on your
personal computer.
The communication between the Central Station and your personal
computer runs on a so-called IP connection. The essential thing in
IP networks is that each participant must have a unique „IP Address".
The units in the network find each other by means of these IP ad-
dresses. A correct IP address must therefore be configured in the
Central Station as well as in your computer; otherwise the exchange
of data will not work.
40

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis