Other Settings; General Settings; Central Station; Components In The System - Märklin Central Station Bedienungsanleitung

5.1 Sniffer Addresses
The Sniffer addresses are stored as an additional property for every
locomotive and are entered in the locomotive menu.
Call up the dialog window „Change Loco" in the locomotive menu,
a procedure you are already familiar with. You can enter the Sniffer
address here.
In the example above, the number 20 was assigned as a Sniffer
address. This means that the locomotive can be controlled from the
6021 with the address 20.
We recommend however that you set the locomotive address and the
Sniffer address to the same value in order to avoid chaos.
• Assign each Sniffer address only once; the Central Station
does not check these addresses.
• Assign the address „0" to locomotives that are not to be
controlled with the old units. This address is fixed at the
outset as a basic setting.
• Only addresses from 01 – 80 can be assigned because of the 6021.
• The Sniffer only recognizes the function buttons „function" or f0
and f1 to f4.
• Never call up a locomotive at the same time on the Central Station
and on the old unit.
• If you no longer want to control a locomotive from the old unit,
stop the locomotive and turn all of its functions off. Enter „0" as
the Sniffer address. After several moments the Sniffer will remove
the locomotive from the internal check list.
• Sniffer addresses are not used for solenoid accessories. The so-
lenoid accessories' adddresses are taken in directly by the Sniffer
and controlled from the Central Station.

6. Other Settings

The Central Station also allows you to change several
basic operations parameters. The submenu "Setup" is
used to do this.
Recommendation: Do not carry out the following steps, until you
have pressed the "STOP" button (emergency stop).
Press the setup symbol in the menu list on the upper edge of the
screen. A selection field will appear, which will give you access to
various selection fields.

General Settings

In this area, you can set the language used on the Central Station,
change the intensity of the background lighting, change the cont-
rast for the screen, change the internal booster current cutoff, and
carry out a „RESET" of the complete unit.
Important:
When you do a
reset of the entire
Central
Station, all
of the data
that has
been entered is
deleted! A reset
of the entire
Central Station is
done without as-
king you a second
time if you want
to have the reset done. The RESET therefore has a gray background
and is blocked.
Do not confuse a reset of the entire Central Station with the reset of
the data in a locomotive!
With the selection list „Internal Booster Current Cutoff" you can re-
duce the current cutoff as desired. Never set the current higher than
necessary in order to avoid damage in the event of a short circuit.
If you want to change the language on the screen, touch the arrow to
call up the outer field. All of the available language versions will ap-
pear, and they can be selected by touching the word for the desired
language. Press the check mark in the lower right to activate it.
The values set for the background lighting and for the contrast are re-
presented by two horizontal bars. The values can be changed either
with the control knob or with the control areas to the right and left of
the bars. The bars must first be activated by touching them so that
the control knob changes the values to the desired ones.
Locomotive Operations Screen Settings
Possible Settings:
1. Assuming control of locomotives: Setting for whether a locomotive
called up on one locomotive controller can be controlled at the
same time on another controller. (parallel operation)
2. Numbering functions: On models with several functions it may
happen that several auxiliary functions (example: sound effects
functions) are displayed with the same symbol. Activating this
function will result in consecutive numbering of these symbols.
3. Start Mode: Setting for whether the former operating data for loco-
motives (speed, direction of travel) is sent out to the models again
after the Central Station is turned on.
These functions are activated or deactivated by touching the square
control area before the text for each function.

Components in the System

With this submenu you can change various defaults for other com-
ponents (Mobile Station) connected to the Central Station. All of the
recognized components are first presented in a selection window.
Using the
methods
already
described
before in
this manu-
al, select
the desired
component
in this window.
In our example in the upper right we are dealing with a Mobile Station
connected to the Central Station.
39
Central Station mit Update 60212