Herunterladen Inhalt Inhalt Diese Seite drucken

Controlling; Connections For Decoder - Märklin Central Station Bedienungsanleitung

Vorschau ausblenden Andere Handbücher für Central Station:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

3.4.2 Running Shuttle Trains
After you have set up the shuttle routes, you can send a train „on the
route". If you are still in the dialog window „Shuttle Train", press on
the check mark, and you will be in the menu „Select Loco".
Important: You must adhere strictly to the sequence in the following
text on the subject „Running a Shuttle Locomotive"!
• First, select the locomotive on one of the two locomotive controllers.
• Place the train on your layout in Station 1 or run the train to this
station.
• Run the train in the shuttle route with the desired speed to
Station 2. Press the STOP button during the run!
• Touch the menu button above. The selection menu will appear and
you can find your routes under „Shuttle Train".
• Use the locomotive controller to mark the route you have chosen.
• Now touch the marked shuttle train.
• The selection window disap-
pears; the selected locomotive
appears again with the speed
curve, the speed that has been
set, and with a small steam lo-
comotive symbol with 2 arrows
to indicate that the shuttle
train control has taken over the
locomotive, not the locomotive
controller.
• Press the GO button. The
locomotive accelerates to the
pre-set speed in the shuttle
train control and is now cont-
rolled only by the latter.
In order to control other locomotives again with the locomotive con-
troller, press the locomotive selection button and select locomotives
as you would usually do. The train on the shuttle route will run back
and forth as long as there is voltage in the track or until the locomo-
tive is removed as outlined in Chapter 3.4.3.
3.4.3 Canceling a Shuttle Train
In order to control a locomotive with the locomotive controller again,
it is removed from shuttle train control as follows:
• Press on the locomotive button.
• Select the locomotive to be removed. The locomotive will appear
with the speed curve as described before.
• Press on the menu button above. The selection menu will appear.
• Press on „Shuttle train". „End Shuttle Train" will appear. Press on
this menu bar. The locomotive will be removed from the shuttle
route and can be controlled from the locomotive controller again.
The shuttle route will remain as before.
4. Controlling Solenoid Accessories
Under the heading solenoid accessories are all of those accessories
on a model railroad layout that are activated with one or more elec-
tromagnetic solenoid mechanisms. Among these types of acces-
sories are turnouts, signals, uncoupler tracks, etc. Lights or motors
activated by a relay also belong to this group. Since the k 84 decoder
has four permanently installed relays, all products connected to this
decoder also belong to this group.
Important! The Central Station can only activate solenoid accesso-
ries, when they are controlled according to the Märklin Digital
format by means of a Märklin k 83 or k 84 decoder or some
other Märklin solenoid accessory decoder (example: 74460 C
Track decoder). Damages arising from the use of other makes
of decoders are not covered by the Märklin factory warranty!
4.1 Connections for Decoders
The k 83 or k 84 decoders can be connected to the system in three
different ways:
1. The decoder takes its data and power for the solenoid accessories
connected to it from the track powered by the Central Station.
2. A ring circuit is set up from the Central Station for powering deco-
ders. To do this, two 72090 distribution strips are inserted between
the track layout and the Central Station, and additional wires are
then connected from the distribution strips to the decoders.
3. The decoders can also be connected to a Booster instead of di-
rectly to the Central Station. Here too, the power for the decoders
can be taken either from the track receiving its power from the
Booster from a separate set of wires connected directly to the
output terminals on the Booster.
Tip: On large layouts it is best to separate the power supply for
the operation of the trains from that for the operation of the
accessories and power the two groups with their own power
units (Central Station, Boosters).
4.2. Setting up / Processing Solenoid Accessories
A turnout or signal must first be taken into the internal solenoid
accessory list, so that the accessory in question can be set up on
the activation field on the Central Station. This can be done either
separately in advance using the "Setting up / Processing Solenoid
Accessories" submenu or when generating the activation fields.
Recommendation: Do not carry out the following steps, until you
have pressed the "STOP" button (emergency stop).
Submenu „Setting Up / Processing Solenoid Accessories"
Press on the symbol „Setting Up Solenoid Accessories"
in the upper menu list on the screen. A selection surface
with six different selection fields will appear:
1. Entering new solenoid accessories
2. Processing solenoid accessories
3. Deleting solenoid accessories
35
4. Enter new route
5. Edit route
6. Delete route
Central Station mit Update 60212

Quicklinks ausblenden:

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis