Herunterladen Inhalt Inhalt Diese Seite drucken

Operating; Operation; Cleaning - Parkside PGI 1200 A1 Originalbetriebsanleitung

Vorschau ausblenden Andere Handbücher für PGI 1200 A1:
Inhaltsverzeichnis

Werbung

Verfügbare Sprachen

Verfügbare Sprachen

Close the oil filler cap (13) and stand the generator
upright
Putting in fuel (Fig. 1/7)
Keep away from ignition sources! Always refuel in
well-ventilated rooms or outside. Open the fuel tank
cap (2) and, using a filler pipe (not included in de-
livery), pour in a maximum of 4.2 litres of unleaded
fuel into the fuel container. Ensure the tank level
is not exceeded and no fuel is spilled. Use the fuel
filter. Clean up spilled fuel immediately and wait until
the fuel fumes have evaporated (fire hazard). Close
the fuel tank cap (2).

7. Operating

Start the engine (Fig. 1/3/6 )
ATTENTION! When starting with the express start
you can injure your hand with the sudden kick back.
Wear protective gloves when starting.
1.
Open the petrol tap by turning the tap down-
wards.
2.
Put the on / off switch (6) to the on position.
3.
Turn the choke lever (9) to I I (in the left posi-
tion).
4.
Start the engine with the express start (10) by
sharply pulling the handle. If the engine has not
started pull the handle again.
5.
Push the choke lever (9) back once the engine
has started (in the right position).
6.
Connect the device to the 230 V~ socket (8).
ATTENTION! This socket can be loaded continu-
ously (S1) with 1000 W and short term (S2) for a
maximum of 5 seconds with 1200 W.
Note: Some electric devices (sabre saws, drills etc.)
can use more electricity when doing heavy duty
tasks.
Storing the engine (Fig. 1/6)
Before putting away, let the generator run without
load so that the device can „cool down".
Turn the on / off switch to the „OFF" position.
Close the petrol tap.
Overload protection 230 V~ socket
WARNING! This generator is fitted with an overload
protector.
This cuts off the sockets
Green operating bulb
Flashes 1 x per interval
Speed too low
Flashes 2 x per interval
Temperature too high
Flashes 3 x per interval
Overload protection
switches on
Flashes 4 x per interval
Short circuit
The socket (8) can be used again after the overload
protection has been triggered once the engine has
been switched off and restarted (See "Turning off
engine" and "Starting engine").
32
GB
ATTENTION! If this happens reduce the amount of
electrical output which you are extracting from the
generator or remove defective devices which are
attached.
ATTENTION! Faulty overload switches should only
be replaced with identically constructed overload
switches with the same performance data. Please
use our customer service department.
Cleaning, maintenance, storage,
transport and ordering
replacement parts
Before cleaning and maintenance work, turn off the
engine and pull the spark plug connector (15) out of
the spark plug (16) .
WARNING! Risk of burning! Wait until the machine
has cooled down before cleaning or servicing it.
ATTENTION! Turn the device off immediately and
contact your Service Station:
With unusual vibrations or noises.
If the engine seems overloaded or has back-
fired.

8. Cleaning

Keep the safeguards, air vents and the engine
housing as dust and dirt free as possible. Wipe the
device with a clean cloth or blow it with compressed
air with low pressure. We recommend that you clean
the device after every use. Regularly clean the de-
vice with a damp cloth and a little soft soap. Do not
use any cleaning products or solvents which could
attack the plastic part of the device. Ensure that no
water can penetrate the housing.
Air filter (Fig. 4)
Also refer to the service information.
Clean the air filter regularly, and if necessary
exchange it.
Open the air filter cover (11) by removing the 2
Phillips head screws M6x16 mm.
Remove the filter element
When cleaning the element do not use any
strong cleaners or petrol.
Clean the element by tapping it on a flat sur-
face.
If it is very dirty wash with soapy water, rinse
with clean water and leave to dry.
Put it back together in the opposite order.
Spark plug (Fig. 6)
Check the spark plug (16) after the first 20 hours of
use for dirt and if necessary clean it with a copper
wire brush. Then service the spark plug after every
50 hours of use.
Remove the spark plug connector (15) with a
turning movement.
Remove the spark plug (16) with the spark plug
socket 25 included.

Werbung

Inhaltsverzeichnis
loading

Inhaltsverzeichnis