Herunterladen Diese Seite drucken

Powerfix Z25679A Bedienungsanleitung Seite 4

Tür-fliegengitter
Vorschau ausblenden Andere Handbücher für Z25679A:

Werbung

Verfügbare Sprachen
  • DE

Verfügbare Sprachen

  • DEUTSCH, seite 19
Safety advice / Prior to assembly / Assembly
The fly screen panels
result in injury and / or damage.
J
CaUTION! FIrE HaZarD! Do
not light an open fire anywhere near
the product.
J
Do not hang anything on the product.
J
First make sure that the material of your door is
suitable for installation of self-adhesive materials.
J
Take care that you do not get caught on the fly
screen panels
when you pass through, since
3
they may otherwise tear off.
Prior to assembly
Q
j
Keep the loop tape
direct sunlight prior to assembly. Excessive heat
can diminish the strength of the adhesive strips.
j
Clean the door frame thoroughly before install-
ing the product. The door frame must be clean,
free from grease and dry before you install the
fixing rail
or the loop tape
2
not the case, the strength of the adhesive strips
may be reduced.
assembly
Q
Permanent installation
Q
of the door fly screen
CaUTION! rISK OF INJUrY! You will
need a saw for this part of assembly. Please make
sure that you consult the operating instructions for
your saw and use protective gloves.
j
First measure the width of your door using a
tape measure (see Fig. A).
Note: The product is suitable for doors with a
maximum width of 100 cm.
j
Shorten the fixing rail
required width using a saw (see Fig. B).
j
Remove the cover
(see Fig. C)
4
GB/IE/CY
may tear off. This can
3
and fixing rail
out of
5
2
on it. If this is
5
and cover
to the
2
1
from the fixing rail
1
2
j
Remove the protective film from the adhesive
strip on the back of the fixing rail
the fixing rail
directly onto the door frame
2
(see Fig. C - E). Use a spirit level if necessary.
j
Wait 2 hours before continuing with assembly.
j
Measure the height of your door using a tape
measure (see Fig. F).
Note: The product is suitable for doors with a
maximum height of 220 cm.
j
Remove the protective film from the adhesive
strip on the front of the fixing rail
j
Stick the fly screen panels
strip on the fixing rail
Note: Take care that the fly screen panels
overlap by at least 10 cm.
Note: Take care that the fly screen panels
end at floor level. Any excess fly screen should
protrude at the top.
j
Cut off any excess fly screen (see Fig. G).
Note: Always cut off excess fly screen at the
top - never at the bottom. The fly screen panels
may otherwise fray.
3
j
Place the cover
1
(see Fig. H).
Temporary installation of the
Q
door fly screen
CaUTION! rISK OF INJUrY! You will need
a saw for this part of assembly. Please make sure
that you consult the operating instructions for your
saw and use protective gloves.
j
First measure the width of your door using a
tape measure (see Fig. A).
Note: The product is suitable for doors with a
maximum width of 100 cm.
j
Shorten the fixing rail
required width using a saw (see Fig. B).
j
Shorten the loop tape
the required width with a pair of scissors.
j
Remove the protective film from the adhesive
strip on the loop tape
onto the door frame (see Fig. I). Use a spirit
level if necessary.
and stick
2
.
2
onto the adhesive
3
(see Fig. F).
2
on the fixing rail
2
and cover
to the
2
1
and hook tape
5
4
and stick the tape
5
3
3
to

Werbung

loading

Diese Anleitung auch für:

Z25679b