Hitachi P 14DSL Bedienungsanleitung Seite 17

3. Adjusting the cutter depth
(1) Turn the knob in the direction indicated by the arrow in
Fig. 10 (clockwise), until the triangular mark is aligned
with the desired cutting depth on the scale. The scale unit
is graduated in millimeters.
(2) The cutting depth can be adjusted within a range of 0-2.0
mm.
4. Surface cutting
Rough cutting should be accomplished at large cutting
depths and at a suitable speed so that shavings are
smoothly ejected from the machine.
To ensure a smoothly fi nished surface, fi nish cutting
should be accomplished at small cutting depths and at
low feeding speed.
5. Beginning and ending the cutting operation
As shown in Fig. 11, place the front base of the planer on
the material and support the planer horizontally. Turn ON
the power switch, and slowly operate the planer toward
the leading edge of the material. Firmly depress the front
half of the planer at the fi rst stage of cutting, as shown in
Fig. 12, depress the rear half of the planer at the end of
the cutting operation. The planer must always be kept fl at
throughout the entire cutting operation.
6. Precaution after fi nishing the planing operation
When the planer is suspended with one hand after
fi nishing the planing operation, ensure that the cutting
blades (base) of the planer do not contact or come too
near your body. Failure to do so could result in serious
injury.
7. Stand
Lift the back of the planer to extend the foot from the
base. Having the stand extended when you put the
planer down prevents contact between the blade and the
material. (Fig. 13)
8. Regulating the guide (Fig. 14)
The planing position can be regulated by moving the
guide to the left or right after loosening its set screw. The
guide may be mounted on either the right or left side of
the tool.
Work Precautions
◯ About Continuous Operation
This tool is provided with a protective function to extend
battery life.
The battery may become overheated during continuous
operation or deep cutting operations, which may cause it
to automatically stop.
Especially with any of the batteries listed below, the tool
may stop operation before the battery starts to get hot to
prevent rapid failure from overheating.
If this happens, stop operation, remove the battery from
the tool and leave it in a well-ventilated location not
exposed to sunlight until it is suffi ciently cool.
The battery can be used again once it is cool.
(Applicable batteries: BSL1425, BSL1420, BSL1415,
BSL1825, BSL1820, BSL1815 and old batteries)
◯ Proper Battery Usage
When the tool is used with any of the batteries listed
below, it should be used for light work to extend battery
life.
Work example: Shallow depth fi nishing and chamfering
work
(Applicable batteries: BSL1425, BSL1420, BSL1415,
BSL1825, BSL1820, BSL1815 and old batteries)
CARBIDE BLADE ASSEMBLY AND
DISASSEMBLY AND ADJUSTMENT OF CUTTER
BLADE HEIGHT (FOR DOUBLE EDGED BLADE
TYPE)
1. Carbide blade disassembly
CAUTION
○ To prevent accidents, ensure that the power tool is
switched off and pull out the battery.
○ Be careful not to injure your hands.
(1) As shown in Fig. 15, loosen the blade holder with the
attached box wrench.
(2) As shown in Fig. 16, remove the carbide blade by sliding
it with the attached box wrench.
2. Carbide blade assembly
CAUTION
○ To prevent accidents, ensure that the power tool is
switched off and pull out the battery.
○ Prior to assembly, thoroughly wipe off all swarf
accumulated on the carbide blade.
(1) As shown in Fig. 17, lift set plate (B) and insert the new
carbide blade between cutter block and set plate (B).
(2) As shown in Fig. 18, mount the new carbide blade by
sliding it on the set plate (B) so that the blade tip projects
by 1mm from the end of the cutter block.
(3) As shown in Fig. 19, fi x the bolts at the blade holder after
blade replacement has been completed.
(4) Turn the cutter block over, and set the other side in the
same manner.
3. Adjustment of carbide blade height
CAUTION
○ To prevent accidents, ensure that the power tool is
switched off and pull out the battery.
○ If the carbide blade's heights are inaccurate after
above procedures have been completed, carry out the
procedures described below.
(1) As shown in Fig. 20, use the box wrench to loosen the
three bolts used to retain the carbide blade, and remove
the blade holder.
(2) As shown in Fig. 21, after removing the carbide blade,
slide set plate (B) in the direction indicated by the arrow
to disassemble set plate (B).
(3) Loosen the 2 screws holding on the carbide blade and
set plate (A), set plate (B).
(4) As shown in Fig. 22, 23, press the turned surface of set
plate (A) to the wall surface b while adjusting the carbide
blade edge to the wall surface a of the set gauge. Then,
tighten them with the 2 screws.
(5) As shown in Fig. 24, 25, insert a turned portion of set
plate (A) attached to set plate (B) into a groove on the fl at
portion of the cutter block.
(6) As shown in Fig. 26, place the blade holder on the
completed assembly and fasten it with the three bolts.
Ensure that the bolts are securely tightened. Follow the
same procedures for the opposite side carbide blade.
BLADE ASSEMBLY AND DISASSEMBLY
AND ADJUSTMENT OF BLADE HEIGHT (FOR
RESHARPENABLE BLADE TYPE)
1. Blade disassembly
CAUTION
○ To prevent accidents, ensure that the power tool is
switched off and pull out the battery.
○ Be careful not to injure your hands.
(1) As shown in Fig. 20, use the accessory box wrench
to loosen the three bolts used to retain the blade, and
remove the blade holder.
English
17